Makita 4341T Manual de instruções - Página 8

Procurar online ou descarregar pdf Manual de instruções para Ferramenta eléctrica Makita 4341T. Makita 4341T 13 páginas. Jig saw
Também para Makita 4341T: Especificações (2 páginas)

Imprimir página

Removing saw blade

CAUTION:

When you remove the saw blade, be careful not to hurt

your fingers with the top of the blade or the tips of work-

piece.

Open the tool opener to the position shown in the figure.

Pull the saw blade out toward the base. (Fig. 3)

NOTE:

Occasionally lubricate the roller.

Selecting the cutting action (Fig. 5)

This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action

thrusts the blade forward on the cutting stroke and greatly increases cutting speed.

To change the cutting action, just turn the cutting action changing lever to the desired cutting action position.

Refer to the table below to select the cutting action.

Position

Straight line cutting action

Small orbit cutting action

Medium orbit cutting action

Large orbit cutting action

III

Switch action (Fig. 6)

CAUTION:

Before plugging in the tool, always check to see that the

tool is switched off.

To start the tool, slide the switch lever to the "I" position.

To stop the tool, slide the switch lever to the "O" position.

Speed adjusting dial (Fig. 7)

For 4341CT, 4341FCT only

The tool speed can be infinitely adjusted between 800

and 2,800 strokes per minute by turning the adjusting

dial. Higher speed is obtained when the dial is turned in

the direction of number 5; lower speed is obtained when

it is turned in the direction of number 1. Refer to the table

below to select the proper speed for the workpiece to be

cut. However, the appropriate speed may differ with the

type or thickness of the workpiece. In general, higher

speeds will allow you to cut workpieces faster but the ser-

vice life of the blade will be reduced.

Workpiece to be cut

Wood

Mild steel

Stainless steel

Aluminum

Plastics

CAUTION:

The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

Cutting action

Number on adjusting dial

4 – 5

3 – 5

3 – 4

3 – 5

1 – 4

Hex wrench storage (Fig. 4)

When not in use, the hex wrench can be conveniently

stored.

Applications

For cutting mild steel, stainless steel and plastics.

For clean cuts in wood and plywood.

For cutting mild steel, aluminum and hard wood.

For cutting wood and plywood.

For fast cutting in aluminum and mild steel.

For fast cutting in wood and plywood.

For 4341CT, 4341FCT only

The tools equipped with electronic function are easy to

operate because of the following features.

Constant speed control

Electronic speed control for obtaining constant speed.

Possible to get fine finish, because the rotating speed is

kept constant even under load condition.

Soft start feature

Safety and soft start because of suppressed starting

shock.

Lighting up the lamps (For 4341FCT only)

CAUTION:

Do not look in the light or see the source of light directly.

To turn on the lamp, pull the trigger. Release the trigger

to turn it off.

NOTE:

Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower the

illumination.

Operation (Fig. 8)

CAUTION:

Always hold the tool base flush with the workpiece. Fail-

ure to do so may cause blade breakage, resulting in a

serious injury.

Turn the tool on and wait until the blade attains full speed.

Then rest the tool base flat on the workpiece and gently

move the tool forward along the previously marked cut-

ting line. When cutting curves, advance the tool very

slowly.