JAMEC PEM 58.4012 Instruções de utilização - Página 2

Procurar online ou descarregar pdf Instruções de utilização para Ferramentas JAMEC PEM 58.4012. JAMEC PEM 58.4012 3 páginas.

Imprimir página
WATER HOSE REEL
PRO SERIES EXTREME- RETRACTABLE
20 M
Extreme Ultraflex Reinforced Hose is a special blend of hose that has been
developed for today's demanding conditions, it stays flexible in the cold and
doesn't kink in the heat, allowing full flow in all-weather conditions. It's a tough
hose for tough conditions
FEATURES
Hose layering system
■
Auto lock / auto rewind
■
Solid brass internal spindle
■
No tools required adjustable hose stop
■
Wall mount with 180° pivot
■
Weather resistant UV stabilised polypropylene case
■
Leader hose 2 m with brass fittings
■
Includes Jamec Pem Extreme Ultraflex Hose
■
Includes water trigger gun
■
SPECIFICATIONS
Hose length
Hose I.D
Hose O.D
Leader hose length
Hose material
Reel / case type
Auto lock / rewind
Max. working pressure
Fitting size
Bracket
Product dimensions
Weight
Application
MAINTENANCE
Always keep the hose clean.
„
If the hose becomes dirty, clean it with a damp cloth while retracting.
„
DO NOT twist the hose while in use.
„
Mount the hose reel in a sheltered area to assist and protect the performance of
„
the hose and hose reel.
DO NOT allow the hose to contact any corrosive chemicals or fluids.
„
5
2
4
1
6
3
20 m
10.5 mm (1/2")
16.5 mm (5/8")
2 m with brass tap female fitting
Extreme Ultraflex Reinforced Hose
Retractable / polypropylene
Yes
150 psi
12 mm Tap fittings
180° Pivoting
569 L x 246.4 W x 441.6 H mm
9.5 kg
Water
Always retract the
„
hose when not in use.
The Jamec Pem
„
Water Hose Reel Pro
Series Retractable
8
contains a pre-
tensioned spring
inside the inner drum
assembly.
9
Do not attempt to
open the inner drum
assembly.
7
0.8 metre min.
PRODUCT IDENTIFICATION
Mounting bracket
1.
Optional fixed in-line locking plate
2.
Pivot pin
3.
Fully enclosed case
4.
Carry handle
5.
Solid brass internal spindle
6.
2 Metre leader hose
7.
Hose with adjustable stopper
8.
Water gun
9.
INSTALLATION
The Jamec Pem Water Hose Reel Pro Series Retractable can
be mounted in a horizontal or vertical position.
Chose a location that is near to the water source.
1.
For large areas, place the hose reel at the centre of the
2.
work area.
When mounting the hose reel vertically, ensure there is
3.
adequate clearance under the reel to prevent injury or
damage.
Mounting bracket must be installed on a flat surface.
4.
Note: It is recommended to install the mounting bracket
5.
0.8 metre (minimum) above the floor level.
Drill 4 x M8 holes to match the holes located in the Mounting Bracket.(Fig. 1)
6.
Connect the hose reel to the Mounting Bracket with the Pivot Pin.(Fig. 2)
7.
Note: For fixed in-line position, fit the locking plate onto the Mounting Bracket prior to
inserting the pivot pin. (Fig. 3)
Connect the inlet leader hose to the water source using the tap fittings supplied.
8.
OPERATION
Slowly pull out the hose to the required length. A 'clicking' noise will be heard
1.
every revolution of the inner drum. To lock the reel, allow the hose to retract slowly
after hearing the second or third 'click'.
To release the hose, pull out the hose until the 'clicking' noise stops, and then
2.
allow the hose to slowly retract while guiding the hose back into the hose reel. The
self layering mechanism will coil the hose back onto the inner drum.
To avoid injury and damage, always hold the hose while it is retracting.
3.
IMPORTANT:
If the hose becomes tangled and will not retract - slowly pull out the hose
past the tangled section and then allow the hose to slowly retract while
guiding the hose back into the hose reel.
Always ensure the hose is clean and not twisted.
Fig. 1 Mounting Bracket
Fig. 2 Pivot Pin
Fig. 3 Locking Plate