GARDEN MASTER GM3830 Instruções de montagem - Página 2

Procurar online ou descarregar pdf Instruções de montagem para Casas de jardim GARDEN MASTER GM3830. GARDEN MASTER GM3830 2 páginas. Gable roof shed

Imprimir página

GARDEN MASTER GM3830 Instruções de montagem

If you feel confident that you do not need to read through these instructions, see page 2....

If you choose to vary from these instructions your warranty will be impaired.

Basic overview of what I am trying to achieve...

"For those of us who do not like reading instructions...."

Just join the sheets together and fit the channels to the top and bottom of the sheets as a framing to

make 4 walls and the roof. Follow these basic steps:....

Front Wall:

Layout 2 x (A) 1830mm sheet, (C) sheet with door jamb attached and (D) door with the sheet

attached beside them to your preferred configuration and join sheets. Cap the sheets with (F) 3745 channels

(2 sided cutout - Top and 1 sided cutout - bottom). Use (H) Door spacers to make sure door fits gap OK

(they sit on top of the jambs). Drill & Fix (Rivet or screw) at every 2nd rib. Attach door spacer at each end

thru door jambs and channels. 5 fixings underneath into sheeting pan top and bottom. Fit padbolt.

Back:

Join 5 (A) 1830mm Sheets together. Cap with (F) Channels and fix thru every 2nd rib and at least 1

fixing per sheet thru the back of the channel into the pan of the sheeting. More in high wind areas.

Roof

: Join 5 (A) 1600mm Sheets together. Cap with (E) 3745mm Channels. Fix @ every 2nd rib. Attach (G)

1600 "L"s to ribs at each end of sheeting at corners and 400mm apart in between. Same for 2nd roof panel.

Fit Ridge Beam (I) to one of the roof panels and fix through the bottom flange and at ends.

End walls:

Measure 1523mm to centre of (E) 3045mm channels and cut flanges only (not right through). Join 4 (B) sheets

together to form gable wall. Cap with (E) 3000mm channels at bottom and bend 3045 channels over the top. Slip (J) Large

Gable plates up under top channel and Small Gable plates underneath in centre of gable and fix to ribs and pans. Fix chan-

nels at corners, every 2nd rib in between and in the centre of the gable. 4 fixings up underneath into pan of sheeting and

gable plate, top and Bottom. Same for other end

Assembly:

You have now made up your 6 panels. It‟s just, Join the corners and put the roof on! Make sure you have at

least 6 fixings down each corner when you join the walls. Place, centralise & fix the roof panel that has the ridge beam fitted

on thru the "L" into the top channel on both end walls. 1 at each end for now. Place, centre and fix to the other end wall.

Slip the 2nd roof panel into ridge beam and fix. Inside: up into ridge beam and outside: thru "L"s every 400mm. You now

need to fix down thru every 2nd pan in the roof into the top channels on the front and back walls. More in high wind

areas. Please make sure that you have removed all swarf filings as the rust spots that they produce may hinder any war-

ranty claims.

Generally most fixings are spaced at 300mm apart

Keep fixings in the pans as close to the ribs as possible for added strength.

Ribs will always protrude to the outside of the shed.

Extra internal fixings is strongly recommended in high wind areas.

Detailed instructions with diagrams:....

1: Front Wall

Note that the cutouts go to the inside of the panel to

allow easy fitment of end walls on assembly

You will need:

(A) 2 x 1830mm sheets

(D) Pre-hinged door and sheet

(F) 1 top and 1 bottom Channel

(H) 2 x Door spacers

To hinge the door on the oppo-

site side - simply put the top

(A)

channel on the bottom and

bottom on top.

Inside

Outside

A.Join 2 x (A) 1830 sheets and (D)

or (C) 740mm sheet depending on

which way door is to swing.

Spacer

B.Use (H) door spacer to determine

the correct opening size by placing

on the bottom flange of the door

jambs. Then fit (F) channels to tops

and bottoms of sheeting.

Channel

January 09

Rib

Pan

(F) Channels with

cutouts (as shown).

(A)

C. Outside: Fix channel at

D. Inside: One fixing per sheet

Fix through top and

E. Fit padbolt to the outside of

bottom of channels into

Door jamb & spacer

Door jamb on inside

Note: Higher side of channel

goes to inside of shed

Pg 2

If you feel confident that you do not need to read through these instructions, see page 2....

If you choose to vary from these instructions your warranty will be impaired.

2: Back Wall

You need:

2 x (F) Channels

5 x (A) Sheets

(F)

3: Roof

You need:

4 x (E) Channels

10 x (A) 1600 Sheets

4 x (G) "L"s

1 x (I) Ridge beam

Drawings are diagrammatic

4: End Walls

and are not necessarily to

detail.

You need:

All the (B) Gable Sheets

2 x (E) 3000 Channels

2 x (E) 3045 Channels

4 x (J) Gable plates

Channels will come

short of ends of sheeting

by 10 - 15mm on all

panels

Channels will end

10 - 15 short of

sheeting

corners and every 2nd rib

between and thru door

jambs and spacer

A. Join 4 (B) sheets together to give a gable end wall as shown.

B. Make a cut in the flanges only at (1523mm) the centre of the 3045 channels

at each end up thru channel

C. Cap the bottom of the sheets with a (E) 3000mm channel and bend the cut 3045

underside and thru door

channel over the top of the sheets. Fix at corners only for now.

jambs/spacer

D. Slip (J) Large Gable plate under channel at the top and Small Gable plate under-

door.

neath and fix to sheeting at the

E. Fix the channels at every 2nd rib and thru gable plate into sheeting ribs.

F. 4 fixings up underneath thru channel into pan of sheet

G. Perform the same again for the other end wall.

(F)

(A)

(G)

(A)

See Fig 2

on Page 4

(B)

„s

January 09

Pg 3

A. Join 5 (A) sheets together with

2 fixings thru the overlapping

ribs making sure the ends of the

sheets are flush.

B. Cap sheeting with (F) channels

putting the cutouts top and bot-

tom same as the front wall.

C. Fix the channels thru the end

ribs and every 2nd rib between.

D. Make sure you put at least 1

fixing per sheet up thru the un-

derside of the channel into the

pan of the sheet.

A. Join 5 (A) 1600mm sheets together

same as the back.

B. Cap sheeting with (E) 3745mm chan-

nels.

C. Fix the channels every 2nd rib but not

the corners at this stage

D. Place the short flange of (G) "L" on

top of the rib at 1 end. Make sure ends

are flush with sheeting and put 1 fixing

in the centre to hold the "L". Fix the

corners thru the channels and 1 more

between the corner and the centre

fixing. Perform the same at the other

end and next roof panel

E. Fit (I) Ridge beam to one roof panel

and fix thru internal flange and thru the

ends of the ridge beam into "L".

Door Brace Kit

A.The Door braces can be fitted now or

after you have assembled your shed.

B.Tuck one end of the "Z" between the

bottom channel of the inside of the

door and the sheet. Do the same at the

top overlapping in the centre behind the

padbolt. If you have a locking "T" handle

you will have to run the "Z"s the oppo-

site way to the diagram.

C.Fix the "Z"s at the ends and in the cen-

tre to the channel it is tucked under and

thru the overlap in the centre. 2 or 3

more rivets will be required thru the

door sheeting into the "Z", but they will

need

fixed

through from the out-

side of the door for

neater appearance.

Inside

D.You may need to cut

or bend the flange at

the bottom and top of

"Z" Brace

the "Z" if it catches on

door jamb when open-

ing or closing.

Padbolt