KitchenAid Range Manual de instalação - Página 6

Procurar online ou descarregar pdf Manual de instalação para Gamas KitchenAid Range. KitchenAid Range 7 páginas. 30" wide free-standing, slide-in and drop-in

Imprimir página

CONNECTING THE RANGE

(, _ --'LECTRIC

SUPPLY

• _The range must be installed in accordance with Local and

larized three or four wire plug-in outlet placed at a conven-

National Electric Code (NEC} ANSI/NFPA No. 70-1990.

ient point near the back of the range. The range is then con-

nected to this outlet through an approved range connec'_or

(pigtail) fastened securely to the terminal block with proper

OUTSIDE

WIRING

strain relief at the range and a three or four pronged plug at

Your local utility company will tell you whether the present

the opposite end.

electric service to your home is adequate. It may be neces-

sary to increase the size of the wiring to the house and serv-

RANG E

CONNECTIONS

ice switch to take care of the electrical load demanded by the

range. The kilowatt rating for the range is specified on the

Some models are shipped direct from the factory with serv-

name plate on the range,

ice cords (pigtails) attached. There are no range connec-

tions necessary on these models. Just plug into the range

outlet. On mcdetsnot providedwith a service cord and rood-

HOUSE WIRING

els having a conduit, connection to the power supply is nec-

Most local Building Regulations and Codes require that all

essary. REMEMBER - mobile homes and some LOCAL

CODES DO NOT PERMIT GROUNDING THROUGH NEU-

electrical wiring be done by licensed electricians. All wiring

should conform to Local and National Electrical Codes. This

TRAL. Hence, 4--wireservice MUSTbe provided for suchin-

range requires a single phase three wire 120/240 or a

stallations. All others permit 3-wire service, use COPPER

120/208 volt, 60 Hz, AC circuit. Wiring codes require a bepa-

WIRE ONLY• Make connections as explained below and

rate circuit be run from the main entrance panel to the range

with reference to the appropriateillustration in figure 6. After

and that it be equipped with separate disconnect switch and

installation, insure tightness of all electrical connections and

fuses, either in the main entrance panel or in a separate

replace all covers,

switch and fuse box. In some communities, a solid or flexible

continuous armored conduit must be used from main on-

NOTE: For cord replacement - onJya power- supply cord

trance panel to the terminal box on the rear of the range,

kit rated at 240 volts minimum, 40 amperes, with closed loop

Otherswill permit the termination of the range circuit at a pc-

terminals and marked for use with ranges shall be used.

"TS-

,_..LtST THE _E_

LEG LEVE'LE.q_J TO TIE.l# C._._._._._._._._._RECT

IEEC, H T.

2. ,_JJST

F,,_t3VT LEG LE'_'ELE'7_ 70 AN _oC--_eOX. IEZC, H T'.

3. P(_IT"..rOl_ _

,e,_Z',qE IN TI'-E CUTCIJT.

.l. ,_t,4KE FI_'_L ,_._._t't,.E_r

YO ;',_3N7" LEG LEYEL,.._.

if,. ,eAISE F,_ONFOF ,_,_

- St.ICE T_E 8.4_ C_VE.R (_TZONAL

• .

EQJIFf_--¢'_',; UNDE_ _

LEE t.E'C'_LE._ f,SEE _'LLt._T_ATZON._.

-INS_TALL,4TION CF F,'o, CNT FLOC.qCOVER-

OpT..TCN_L EDUI,_NENT