Gardena ComfortCut 450/25 Manual do operador - Página 6
Procurar online ou descarregar pdf Manual do operador para Aparador Gardena ComfortCut 450/25. Gardena ComfortCut 450/25 9 páginas. Turbotrimmer
Também para Gardena ComfortCut 450/25: Manual de Instruções (16 páginas), Manual de Instruções (16 páginas), Manual de Instruções (15 páginas), Manual de Instruções (16 páginas)
Imprimir página
• for Art. 9808 / 9809:
GARDENA Filament Cassette for Turbotrimmers
• for Art. 9811:
GARDENA Filament Cassette for Turbotrimmers
1. Press in cassette cover
d
on the two catches
remove.
2. Remove the filament cassette
3. Remove any dirt.
4. Pull approximately 15 cm of the cutting filament
g
f ilament cassette
through the hole in the plastic ring
5. First thread the cutting filament
6. For Art. 9808 / 9809 only: Thread the cutting filament
k
guide pin
.
g
7. Insert the filament cassette
d
8. Fit the cassette cover
on the filament cassette holder
you hear both locking clips
f
For Art. 9808 / 9809 only: When fitting the cassette cover
p
filament
must be placed around the guide pin
trapped.
v If the cassette cover
d
cannot be touched down, turn the filament
g
cassette
to and fro, until the filament cassette
the filament cassette holder
l
6. TROUBLESHOOTING
DANGER! Risk of injury from the cutting filament!
v Always unplug the mains plug of the Turbotrimmer
before troubleshooting!
Pulling the filament out of the filament cassette [ Fig. T1 ]:
If a filament is drawn into the filament cassette you can pull it out again as
described below.
1. Remove the filament cassette
"Replacing the filament cassette".
2. Press together the plastic ring
your thumb and forefinger.
3. Draw the plastic ring
h
over the side part of the filament cassette
(use a screwdriver if necessary).
You can now access the filament that was drawn into the filament
cassette.
4. Unwind the cutting filament
p
h
the eye of the plastic ring
. If necessary, loosen the welded filament
beforehand using a screwdriver, and unwind and rewind completely.
5. Pull the plastic ring
h
back over the filament cassette
6. Reinstall the filament cassette
"Replacing the filament cassette".
Problem
Possible Cause
The trimmer no longer cuts
Filament worn or too short.
The trimmer no longer cuts
Filament cassette empty.
Filament drawn into the
cassette or stuck together.
Filament cannot be
The filament became too dry
and brittle (e. g. over the winter).
extended or filament
is consumed rapidly
Frequent contact between the
filament and hard objects.
NOTE: For any other malfunctions please contact the GARDENA service depart-
ment. Repairs must only be done by GARDENA service departments or specialist
dealers approved by GARDENA.
7. TECHNICAL DATA
Turbotrimmer
Unit
Value (Art. 9808) Value (Art. 9809) Value (Art. 9811)
Motor power consumption
W
450
Mains voltage /
V / Hz
230 / 50 – 60
Mains frequency
Art. 5307
Art. 5309
f
at the same time and
g
.
p
out of the new
h
.
p
j
through the metal sleeve
.
p
around the
l
into the filament cassette holder
l
so that
click into place.
d
, the cutting
k
and must not be
g
is completely in
.
g
as described under 5. MAINTENANCE
h
on the filament cassette
g
between
by approx. 15 cm and thread it through
g
.
g
as described under 5. MAINTENANCE
Remedy
v Lengthen the filament
(see 3. OPERATION "Filament
feed – Tip mechanism" ) .
v Replace the filament cas sette
(see 5. MAINTENANCE
"Replac ing the filament
cassette") .
v Pull the filament out of the
filament cassette (see above).
v Place the filament in water
for approx. 10 hours.
v Avoid contact between the
filament and hard objects.
500
650
230 / 50 – 60
230 / 50 – 60
Turbotrimmer
Filament thickness
Cutting width
Filament supply
Filament feed
Rpm of filament cassette
(approx.)
Weight (approx.)
Telescopic adjustment of
the turn handle (approx.)
Sound pressure level L
1)
pA
Uncertainty k
pA
.
Sound power level L
:
2)
WA
measured/guaranteed
Uncertainty k
WA
Hand/arm vibration a
3)
vhw
Uncertainty k
a
Measuring process complying with:
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of
exposure. The vibration emission value can vary during actual use of the electric power
tool.
8. SERVICE / WARRANTY
Service:
Please contact the address on the back page.
Warranty:
In the event of a warranty claim, no charge is levied to you for the services
provided.
GARDENA Manufacturing GmbH offers a two-year warranty (effective
as of the date of purchase) for this product. This warranty includes all
significant defects of the product that can be proved to be material or
manufacturing faults. This warranty is fulfilled by supplying a fully functional
replacement product or by repairing the faulty product sent to us free of
charge; we reserve the right to choose between these options. This ser-
vice is subject to the following provisions:
• The product was used for its intended purpose as per the recommen-
dations in the operating instructions.
• Neither the purchaser nor a third party has attempted to repair the
product.
This manufacturer's warranty does not affect warranty entitlements against
the dealer / retailer.
If problems arise with this product, please contact our Service depart-
ment or send the defective product along with a brief description of the
fault to GARDENA Manufacturing GmbH, making sure to have sufficiently
covered any shipping costs and to have followed the relevant postage
and packaging guidelines. A warranty claim must be accompanied by
a copy of the proof of purchase.
Consumables:
The filament cassette and cassette cover are consumables and are not
covered by the guarantee.
Unit
Value (Art. 9808) Value (Art. 9809) Value (Art. 9811)
mm
1.6
1.6
mm
250
270
m
6
6
Tip mechanism
Tip mechanism
rpm
12,800
12,200
kg
3.3
3.3
cm
24
24
84
83
dB (A)
3
3
93 / 94
94 / 96
dB (A)
1
2
< 2.5
< 2.5
m/s
2
1.5
1.5
1)
DIN EN 60335-2-91
2)
RL2000/14/EG
3)
DIN EN 786.
2.0
300
4
Tip mechanism
10,500 (Idle speed
approx. 9,500)
3.6
24
83
3
93 / 96
3
< 2.5
1.5
9