Gardena 4068 Manual do operador - Página 6
Procurar online ou descarregar pdf Manual do operador para Equipamento para relva e jardim Gardena 4068. Gardena 4068 9 páginas. Electric aerator
Também para Gardena 4068: Manual de Instruções (14 páginas), Manual de Instruções (15 páginas), Manual do operador (9 páginas), Manual de Instruções (14 páginas), Manual de Instruções (13 páginas), Manual de Instruções (13 páginas), Manual de Instruções (15 páginas), Manual do operador (10 páginas)
Imprimir página
1. Place Aerator on flat grass surface.
2. Keep safety interlock
(12)
pressed down and pull starting lever
(3)
upper handle
.
The Aerator starts.
(12)
3. Release safety interlock
.
When in operation, the extension cable
in the direction you are working and to the side of the area to be
worked on.
Always work away from the connection cable.
Blockage Protection: If the aerator cylinder is blocked, e. g. by a for-
eign body, immediately release the starting lever. If the blockage lasts
longer than 10 seconds and the starting lever has not been released,
blockage protection is activated. In this case immediately release the
starting lever. The Aerator can be switched on again after cooling down
for approx. 1 minute.
5. MAINTENANCE
DANGER!
The aerator cylinder can cause injuries!
v Prior to maintenance, unplug from the mains and wait until
the Aerator drum has stopped.
v Wear working gloves for performing maintenance.
Cleaning Aerator:
The Aerator should be cleaned after each time it is used.
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not use hard or pointed objects for cleaning the Aerator.
v Remove grass and deposits from wheels, aerator cylinder and housing.
Adjusting for wear [ Fig. M1 ]:
The Aerator is subject to wear in use due to the way in which it works.
The more intensively the Aerator is used, the greater the wear on the
knives. Hard or very dry ground accelerates wear as does excessive use
of the Aerator.
If the results of your work with the Aerator become increasingly worse
due to knife wear, the aerator cylinder can be adjusted twice.
The aerator cylinder has 4 adjustment positions:
• Transport position
• Aerating position 1
• Aerating position 2:
First adjustment position after knife wear (aerator cylinder lowered
by 3 mm).
• Setting 3:
Second adjustment position after knife wear (aerator cylinder lowered
by a further 3 mm).
Push wear compensation lever
(14)
move to the position required.
Note: Wear adjustment is not used for height adjustment.
Adjustment of the aerator cylinder without visible wear can
cause damage to the aerator cylinder or overload the motor.
6. STORAGE
To put into storage:
To save space the aerator can be folded up by releasing the wing nuts.
Take care during this process that the cable does not become
trapped.
v Store the Aerator in a dry, closed room to which children cannot gain
access.
Transport:
1. Switch off motor, unplug from the mains and wait until the aerator
cylinder stops.
2. Move the wear compensation to the transport position and raise the
aerator when transporting it over sensitive surfaces, e. g. tiles.
10
(13)
on the
(10)
must always be guided
gently away from the housing and
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.
7. TROUBLESHOOTING
Replacing aerator cylinder:
DANGER!
The aerator cylinder can cause injuries!
v Prior to rectifying faults, unplug from the mains and wait until
the aerator cylinder has stopped.
v Wear working gloves when rectifying faults.
If the aerator cylinder is in wear adjustment position 3 and is worn, the
aerator cylinder must be replaced. Only use the original GARDENA
cylinder for art. 4068 which can be ordered via GARDENA-Service.
1. [ Fig. T1 ]: Unscrew two screws
2. [ Fig. T2 ]: Lift aerator cylinder
drive shaft 2.
3. Remove bearing shell
(21)
from the aerator cylinder
4. [ Fig. T3 twisted / T4 new ]: Push new spring
new torsion spring
(19)
into the new aerator roller
5. [ Fig. T5 ]: Push new aerator cylinder
such a way that the torsion spring
drive shaft
(20)
.
6. Push bearing shell
(21)
on to the aerator roller
(21)
7. Screw bearing shell
to the underside of the housing
tightening too much.
8. Set wear compensation to aerator position 1
(see 5. MAINTENANCE Adjusting for wear).
Problem
Possible Cause
Abnormal noise,
Foreign bodies on the aerator
clattering in the unit
cylinder are hitting the Aerator.
Whistling sound
Foreign bodies blocking the
aerator cylinder.
Whistling sound
Cogged belt slipping.
Motor will not start
Faulty cable.
The conductor cross-section
of the extension cable is
possibly too low.
Motor cuts out because
Blocked by foreign bodies.
blocking protection has
been activated
Aerating depth too large
(aerator cylinder has been
adjusted for wear without
wear to the knives).
The grass is too tall.
Aerating results are not
Aerator cylinder is worn.
satisfactory
Cog-belt faulty.
Lawn has grown too tall.
Aerator cylinder no longer
Overload protection (torsion
turns
spring too short) is overturned.
(15)
on the underside of the housing.
(16)
at an angle 1 and pull away the
(16)
.
(17)
, new stop
(18)
and
(16)
.
(16)
on to the drive shaft in
(19)
is inserted in the gap in the
(16)
.
(15)
, without
Remedy
1. Switch off the Aerator, remove
the mains plug from the sock-
et and wait until the Aerator
has stopped rotating.
2. Remove foreign bodies.
3. Check aerator immediately.
immediately.
v Have the machine repaired
by GARDENA Service.
v Check cable.
v Contact your electrician.
1. Switch off the Aerator, remove
the mains plug from the sock-
et and wait until the Aerator
has stopped rotating.
2. Remove foreign bodies.
3. After approx. 1 minute switch
on the Aerator.
1. Leave motor to cool down.
2. Set adjustment for wear
correctly.
v Mow the lawn before
aerating (see 2. FUNCTION
Correct Aerating ).
v Adjust aerator cylinder
(see 5. MAINTENANCE).
v Have the machine repaired
by GARDENA Service.
v Mow the lawn before using
the Aerator.
v Replace torsion bar.