Gardena EVC 1000 Manual do operador - Página 6

Procurar online ou descarregar pdf Manual do operador para Equipamento para relva e jardim Gardena EVC 1000. Gardena EVC 1000 9 páginas. Electric aerator
Também para Gardena EVC 1000: Manual de Instruções (12 páginas), Manual de Instruções (13 páginas), Manual de Instruções (15 páginas), Manual de Instruções (14 páginas), Manual de Instruções (15 páginas), Manual do operador (9 páginas), Manual de Instruções (14 páginas), Manual de Instruções (13 páginas), Manual de Instruções (13 páginas), Manual de Instruções (15 páginas), Manual do operador (10 páginas)

Imprimir página

1. Place Aerator on flat grass surface.

2. Keep safety interlock

(12)

pressed down and pull starting lever

(3)

upper handle

The Aerator starts.

(12)

3. Release safety interlock

When in operation, the extension cable

in the direction you are working and to the side of the area to be

worked on.

Always work away from the connection cable.

Blockage Protection: If the aerator cylinder is blocked, e. g. by a for-

eign body, immediately release the starting lever. If the blockage lasts

longer than 10 seconds and the starting lever has not been released,

blockage protection is activated. In this case immediately release the

starting lever. The Aerator can be switched on again after cooling down

for approx. 1 minute.

5. MAINTENANCE

DANGER!

The aerator cylinder can cause injuries!

v Prior to maintenance, unplug from the mains and wait until

the Aerator drum has stopped.

v Wear working gloves for performing maintenance.

Cleaning Aerator:

The Aerator should be cleaned after each time it is used.

DANGER! Risk of injury!

Risk of injury and risk of damage to the product.

v Do not clean the product with water or with a water jet

(in particular high-pressure water jet).

v Do not use hard or pointed objects for cleaning the Aerator.

v Remove grass and deposits from wheels, aerator cylinder and housing.

Adjusting for wear [ Fig. M1 ]:

The Aerator is subject to wear in use due to the way in which it works.

The more intensively the Aerator is used, the greater the wear on the

knives. Hard or very dry ground accelerates wear as does excessive use

of the Aerator.

If the results of your work with the Aerator become increasingly worse

due to knife wear, the aerator cylinder can be adjusted twice.

The aerator cylinder has 4 adjustment positions:

• Transport position

• Aerating position 1

• Aerating position 2:

First adjustment position after knife wear (aerator cylinder lowered

by 3 mm).

• Setting 3:

Second adjustment position after knife wear (aerator cylinder lowered

by a further 3 mm).

Push wear compensation lever

(14)

move to the position required.

Note: Wear adjustment is not used for height adjustment.

Adjustment of the aerator cylinder without visible wear can

cause damage to the aerator cylinder or overload the motor.

6. STORAGE

To put into storage:

To save space the aerator can be folded up by releasing the wing nuts.

Take care during this process that the cable does not become

trapped.

v Store the Aerator in a dry, closed room to which children cannot gain

access.

Transport:

1. Switch off motor, unplug from the mains and wait until the aerator

cylinder stops.

2. Move the wear compensation to the transport position and raise the

aerator when transporting it over sensitive surfaces, e. g. tiles.

(13)

on the

(10)

must always be guided

gently away from the housing and

Disposal:

(in accordance with RL2012/19/EC)

The product must not be disposed of to normal household

waste. It must be disposed of in line with local environmental

regulations.

IMPORTANT!

v Dispose of the product through or via your municipal recycling

collection centre.

7. TROUBLESHOOTING

Replacing aerator cylinder:

DANGER!

The aerator cylinder can cause injuries!

v Prior to rectifying faults, unplug from the mains and wait until

the aerator cylinder has stopped.

v Wear working gloves when rectifying faults.

If the aerator cylinder is in wear adjustment position 3 and is worn, the

aerator cylinder must be replaced. Only use the original GARDENA

cylinder for art. 4068 which can be ordered via GARDENA-Service.

1. [ Fig. T1 ]: Unscrew two screws

2. [ Fig. T2 ]: Lift aerator cylinder

drive shaft 2.

3. Remove bearing shell

(21)

from the aerator cylinder

4. [ Fig. T3 twisted / T4 new ]: Push new spring

new torsion spring

(19)

into the new aerator roller

5. [ Fig. T5 ]: Push new aerator cylinder

such a way that the torsion spring

drive shaft

(20)

6. Push bearing shell

(21)

on to the aerator roller

(21)

7. Screw bearing shell

to the underside of the housing

tightening too much.

8. Set wear compensation to aerator position 1

(see 5. MAINTENANCE Adjusting for wear).

Problem

Possible Cause

Abnormal noise,

Foreign bodies on the aerator

clattering in the unit

cylinder are hitting the Aerator.

Whistling sound

Foreign bodies blocking the

aerator cylinder.

Whistling sound

Cogged belt slipping.

Motor will not start

Faulty cable.

The conductor cross-section

of the extension cable is

possibly too low.

Motor cuts out because

Blocked by foreign bodies.

blocking protection has

been activated

Aerating depth too large

(aerator cylinder has been

adjusted for wear without

wear to the knives).

The grass is too tall.

Aerating results are not

Aerator cylinder is worn.

satisfactory

Cog-belt faulty.

Lawn has grown too tall.

Aerator cylinder no longer

Overload protection (torsion

turns

spring too short) is overturned.

(15)

on the underside of the housing.

(16)

at an angle 1 and pull away the

(16)

(17)

, new stop

(18)

and

(16)

on to the drive shaft in

(19)

is inserted in the gap in the

(16)

(15)

, without

Remedy

1. Switch off the Aerator, remove

the mains plug from the sock-

et and wait until the Aerator

has stopped rotating.

2. Remove foreign bodies.

3. Check aerator immediately.

immediately.

v Have the machine repaired

by GARDENA Service.

v Check cable.

v Contact your electrician.

1. Switch off the Aerator, remove

the mains plug from the sock-

et and wait until the Aerator

has stopped rotating.

2. Remove foreign bodies.

3. After approx. 1 minute switch

on the Aerator.

1. Leave motor to cool down.

2. Set adjustment for wear

correctly.

v Mow the lawn before

aerating (see 2. FUNCTION

Correct Aerating ).

v Adjust aerator cylinder

(see 5. MAINTENANCE).

v Have the machine repaired

by GARDENA Service.

v Mow the lawn before using

the Aerator.

v Replace torsion bar.