Makita 6207D Manual de instruções - Página 5

Procurar online ou descarregar pdf Manual de instruções para Perfurar Makita 6207D. Makita 6207D 10 páginas. Cordless driver drills 10mm, 13mm
Também para Makita 6207D: Informações técnicas (13 páginas), Manual de instruções (12 páginas)

Imprimir página

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to drill safety rules. If you use this power tool

unsafely or incorrectly, you can suffer serious per-

sonal injury.

Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a "live" wire will make exposed

metal parts of the tool "live" and shock the oper-

ator.

Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

Hold the tool firmly.

Keep hands away from rotating parts.

Do not leave the tool running. Operate the tool

only when hand-held.

Do not touch the drill bit or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the car-

tridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Switch action (Fig. 2)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the "OFF" position when released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Reversing switch action (Fig. 3)

This tool has a reversing switch to change the direction of

GEB002-2

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for counter-

clockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

Speed change (Fig. 4)

To change the speed, first switch off the tool and then

slide the speed change lever to the "2" side for high

speed or "1" side for low speed. Be sure that the speed

change lever is set to the correct position before opera-

tion. Use the right speed for your job.

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned halfway between the "1" side and "2"

side, the tool may be damaged.

• Do not use the speed change lever while the tool is run-

ning. The tool may be damaged.

Selecting action mode (Fig. 5)

This tool has an mode change lever. For drilling, depress

the lock button and then slide the action mode change

lever to the left (

action mode change lever to the right (

it is locked. If it is hard to turn the lever, first turn the

chuck slightly in either direction and then turn the lever

again.

CAUTION:

• Always slide the action mode change lever all the way

to your desired mode position. If you operate the tool

with the lever positioned halfway between the mode

symbols, the tool may be damaged.

• Do not use the action mode change lever while the tool

is running. The tool may be damaged.

Adjusting the fastening torque (Fig. 6)

The fastening torque can be adjusted in 16 steps by turn-

ing the adjusting ring so that its graduations are aligned

with the pointer on the tool body.

FIrst, slide the action mode change lever to the position

symbol.

The fastening torque is minimum when the number 1 is

aligned with the pointer, and maximum when the marking

is aligned with the pointer. The clutch will slip at various

torque levels when set at the number 1 to 16. Before

actual operation, drive a trial screw into your material or a

piece of duplicate material to determine which torque

level is required for a particular application.

CAUTION:

• The adjusting ring does not lock when the pointer is

positioned only halfway between the graduations.

symbol). For screwing, slide the

symbol) until