AC Hydraulic VL10 Manual do utilizador - Página 3

Procurar online ou descarregar pdf Manual do utilizador para Valetes AC Hydraulic VL10. AC Hydraulic VL10 20 páginas. Vertical transmission jack
Também para AC Hydraulic VL10: Manual do utilizador (16 páginas)

Imprimir página

VL3, VL6, VL10

WARNING -

safe usage instructions

Centering the load is essential for a safe lift, so the

centre of gravity of the gearbox must always be placed

in the middle of the transmission jack.

If the position of the centre of gravity is unknown, the

weight distribution must always be evaluated and chan-

ged if needed before the lift continues.

Also remember that transport must only be carried out

with the load lowered.

1. The transmission jack is only to be used by trained

staff, familiar with this User's Guide.

2. The use of this jack is limited to removal, installation,

and transportation in its lowest position, of transmis-

sions, differentials, shafts, etc.

3. Within the weight limitations specified, the jack may

be used with the original adaptors.

4. Be sure that the vehicle is appropriately supported

and chocked before starting repairs.

5. This jack is designed for use only on hard level sur-

faces capable of sustaining the load.

6. Avoid decentral gravity of the load. Decentral pla-

cement of load might cause overturning of load and

transmission jack.

7. All transportation must take place with jack in the

lowest position and load stabilized.

8. Do not overload.

9. No alterations must be made on the transmission

jack or the safety valve.

10. Failure to follow these warnings may result in loss

of load, damage to jack, and/or failure resulting in

personal or property damage.

Assembly

1. Grease spike (40) and assemble pedal (45). in ac-

cordance with drawing.

2. Grease end of pump piston (36).

3. Mount the legs loosely by means of four bolts (27).

4. Tighten the wheels to legs by means of bolts (25),

and tighten to a torque setting of 80 Nm.

5. Place jack on level surface to make pump rest on two

lowest bolts (27). Tighten two through-going bolts be-

fore tightening of two lowest bolts.Negligence of this

procedure might make the jack "3-legged".

Use of Transmission Jack

Lifting: Operate pumping pedal (45)

Lowering: Open release handle (33) by turning it slowly

counterclockwise. The release handle is spring acti-

vated and will close automatically when not activated.

Transport: Lower load to lowest position and check

stability of load before transport.

Maintenance

Daily: Check transmission jack for damages.

Monthly: Lubricate spike (40) of pedal. Grease end of

pump piston (36).

Oil filling: Check oil level with lifting saddle (38) in

lowest position. The correct oil level is to the lower edge

of hole for filling screw (30) with the transmission jack in

its lowest position.

Quantity of oil:

Any good hydraulic oil of viscosity ISO VG 15 can be

used.

Never use brake fluid.

Safety inspection

In accordance with national regulations - yet, at least

once a year - the following parts must be checked by an

expert:The lifting saddle, legs and wheels for incipient

breakage and unnormal wear. Hydraulic parts for leaks.

Function of release valve. Furthermore that all safety

labels are legible.

Troubleshooting

1. The transmission jack does not lift to maximum

height: Check oil level. (see "maintenance")

2. The pump is pumping badly (half strokes): Vacuum

has been created in reservoir because of too much

oil. Check oil level and empty out extra oil.

3. The transmission jack lowers:

Check whether the release is closed tightly.

If not tighten spring max 1/2 turn to the left.

Destruction

Oil must be drained off and legally disposed off.

(Translation of original text)

1,2 l.