Garmin RV-IN1501 Manual do Proprietário - Página 20

Procurar online ou descarregar pdf Manual do Proprietário para Sistema de navegação automóvel Garmin RV-IN1501. Garmin RV-IN1501 36 páginas. Rv infotainment system
Também para Garmin RV-IN1501: Instruções de instalação (4 páginas)

Imprimir página

Connecting a UPnP Device

You must connect your stereo to a network, either wired or

wirelessly, to play media from a UPnP device, such as a NAS

device.

Connect your UPnP device to the same network as the

stereo, referring to the instructions provided with your UPnP

device and router if necessary.

Select the UPnP source on the stereo

page

13).

You can browse and play media from the UPnP device the in

same way that you would from a USB flash drive

Music Playback on a Connected Android Device, USB Flash

Drive, or Media Player, page

Audio Control

Adjusting the Volume for a Zone

Select Fusion Media >

Select a zone.

TIP: To control all zones at the same time, select GLOBAL.

Drag the slider up or down.

Muting all Connected Stereos

You can quickly mute the audio from this stereo or from all

stereos connected to the network

Networking, page

18).

From any source, select .

The mute symbol appears and audio from this stereo is

silenced.

Adjusting the Tones

Select Fusion Media >

Select a zone.

Select TONE.

Use the slider bar to adjust the level of each tone.

Disabling the Loud Setting for a Zone

The LOUD setting maintains frequency response at low volumes

and increases perceived loudness at high volumes. This setting

is enabled by default in all zones.

Select Fusion Media >

Select a zone.

Select LOUD to clear the option button.

Adjusting the Gain for an Auxiliary Device

You can adjust the gain for a connected auxiliary device to

achieve a volume level similar to that of other media sources.

You can adjust the gain in 1 dB increments.

Select an auxiliary source.

Move the slider left or right to increase or decrease the gain.

NOTE: To achieve the best audio quality when using a

portable media player with headphone output, it may be

necessary to adjust the volume control on the media player,

instead of adjusting the gain.

Speaker Zones

You can group speakers in one area into a speaker zone. This

enables you to control the audio level of the zones individually.

For example, you could make the audio quieter in the cabin and

louder on deck.

You can set the balance, volume limit, tone, subwoofer level,

subwoofer frequency, and name for each zone, and configure

other zone-specific settings

Adjusting the Audio Settings for a Zone

Select Fusion Media >

Select a zone.

(Selecting a Source,

(Controlling

15).

(FUSION PartyBus

™

> ZONE.

(Speaker Zone Settings, page

> ZONE.

Select MORE.

Select one or more options:

NOTE: Not all options are available for all zones.

• To limit the maximum volume output of this zone, select

VOLUME LIMIT, and adjust the level.

• To set the subwoofer level for this zone, select SUB

LEVEL, and adjust the level.

• To adjust the right and left speaker balance of this zone,

select BALANCE, and adjust the balance.

Adjusting the Subwoofer Filter

You can use the subwoofer filter setting to control the subwoofer

cutoff frequency for each zone, which can enhance the blend of

the sound produced by the speakers and the subwoofer. Audio

signals above the selected frequency are not passed to the

subwoofer.

NOTE: If a DSP setting has been applied to zone, this setting

cannot be changed on the stereo. You can view the DSP setting

for the optimal cutoff frequency as calculated by the DSP

controller, but cannot adjust it.

Select Fusion Media >

Select a zone.

Select SUB FREQ.

Select a frequency.

DSP Settings

This stereo features digital signal processing (DSP). You can

select pre-configured DSP settings for FUSION

amplifiers to optimize audio reproduction in their installed

locations.

All DSP settings are configured using the FUSION-Link

control app

(FUSION-Link Wireless Remote Control App,

page

20).

Configuring the DSP Settings

You must download and install the FUSION-Link remote control

app on your compatible Apple or Android device before you can

configure the DSP settings

Control App, page

You can configure the DSP settings to optimize the sound on

each zone with the installed speakers, amplifiers, and

environment.

From the settings menu on your Apple or Android device,

connect to the stereo using Bluetooth technology, or connect

to the same wireless network as the stereo.

Open the FUSION-Link remote control app on your

compatible Apple or Android device.

If necessary, select the stereo you want to configure.

Select

> MUSIC SETTINGS.

Select a zone.

Select DSP SETTINGS.

Configure the DSP settings as needed, depending on the

models of FUSION speakers and amplifiers connected to the

zone.

Repeat these steps for each zone.

After you have finished configuring the DSP settings for all

zones, select an option:

• On an Apple device, select

SEND DSP SETTINGS

• On an Android device, select

SETTINGS.

19).

Bluetooth Device Playback

You can pair the stereo to up to eight Bluetooth media devices.

> ZONE.

(FUSION-Link Wireless Remote

20).

> Zone > SETTINGS >

> Zone > SEND DSP

speakers and

™

remote

Media Playback