Garmin GPS 17HVS - Receiver Module Especificações técnicas - Página 30

Procurar online ou descarregar pdf Especificações técnicas para Sistema GPS marítimo Garmin GPS 17HVS - Receiver Module. Garmin GPS 17HVS - Receiver Module 34 páginas. Declaration of conformity
Também para Garmin GPS 17HVS - Receiver Module: Manual de instruções de instalação (12 páginas), Manual de instalação (16 páginas), Especificações técnicas (40 páginas), Especificações técnicas (37 páginas), Declaração de Conformidade (2 páginas)

APPENDIX D: GPS 17X HVS AND WINDOWS SERIAL MOUSE ISSUE

Problem: It is possible for Windows to incorrectly interpret the NMEA 0183 output of the GPS 17x HVS as the

output of a Microsoft Serial BallPoint Mouse. When that happens, Windows loads drivers for the Serial BallPoint

Mouse. This causes the cursor to move erratically about the display, clicking, right-clicking, double-clicking,

dragging and dropping displayed items as it goes. On Windows 2000 and Windows XP, you may not experience the

problem if you wait until after the computer is booted before connecting the GPS 17x HVS to the serial

communications port. This problem is not specific to the GPS 17x HVS. Any NMEA 0183 device connected to a

Windows computer's serial port is likely to cause this problem. Below are several possible solutions to this problem.

If you wish to use a different navigation software application with your GPS 17x HVS, you will need to de-select

the "Binary Output Data" option that is discussed in Solution 3 below.

Solution 1: The easiest solution is to disable the Serial BallPoint mouse in the Device Manager. This solution

assumes that you do not need to use a Serial BallPoint mouse with your computer. When erratic mouse movements

occur, follow the steps below.

1. Unplug the DB9 connector.

2. Right-click the My Computer icon on your desktop and select Properties to open Device Manager.

3. Go to the hardware tab of the resulting pop-up window and click on the Device Manager button.

4. Right-click on Serial BallPoint Mouse and choose the option to Disable (NOT uninstall) this device.

Solution 2: Do not plug the DB9 connector into the computer until the computer is turned on and the operating

system is completely booted up and running. Every time you use the GPS 17x HVS, you will need to start the

computer and operating system before making the connection between the GPS 17x HVS and the computer. This

solution usually works on Windows 2000 and Windows XP computers.

Solution 3: Change the default output of the GPS 17x HVS so that it does not automatically send NMEA 0183 data

to the computer (change the default configuration to enable "Binary Output Data"). Use the Garmin Sensor

Configuration Software, named SNSRXCFG.EXE, provided on the Web site to enable "Binary Output Data." To

download the software, start at www.garmin.com/oem, select the GPS 17x HVS, and then select Updates and

Downloads.

Please note that by enabling "Binary Output Data," the device will no longer appear as a NMEA 0183 device to your

computer. As a result, mapping applications that expect to hear NMEA 0183 data will not recognize your GPS 17x

HVS until you re-enable the NMEA 0183 output, disabling the "Binary Output Data" in the process.

Refer to

Appendix E: Sensor Configuration Software

Configuration Software application.

After the Sensor Configuration Software is installed and running on your computer, follow the steps below to

change the default data output of the GPS 17x HVS.

1. Select GPS 17x from the list of sensors and click OK. The

Sensor Configuration Software opens with the default

configuration file for the GPS 17x HVS, as shown on the next

page.

2. Select Config > Switch to NMEA Mode (or press the F10 key).

3. Select Comm > Setup to open the Comm Setup Window.

190-00885-07

for complete information about downloading the Sensor

GPS 17x HVS Technical Specifications

Page 26

Rev. A