Garmin Reactor 40 Manual de instruções de instalação - Página 6
Procurar online ou descarregar pdf Manual de instruções de instalação para Equipamento marítimo Garmin Reactor 40. Garmin Reactor 40 11 páginas. Mechanical
Também para Garmin Reactor 40: Manual de instruções de instalação (13 páginas), Manual de instruções de instalação (29 páginas), Manual de configuração (8 páginas), Manual de instruções de instalação (25 páginas)
Imprimir página
NOTE: The braided drain wire (bare) on the NMEA 2000
power cable must be connected to the same ground as the
black wire on the NMEA 2000 power cable.
3
Connect the NMEA 2000 power cable to one of the T-
connectors.
4
Connect one of the included NMEA 2000 drop cables
one of the T-connectors and to the helm control (optional) or
to a compatible Garmin chartplotter
5
Connect the other included NMEA 2000 drop cable to the
other T-connector and to the CCU
6
Connect the male and female terminators
the combined T-connectors.
Connecting the Autopilot Components to an Existing NMEA
2000 Network
A dedicated helm control is not included in all autopilot
packages. If you install the autopilot without a dedicated helm
control, the autopilot CCU must be connected to the same
NMEA 2000 network as a compatible Garmin chartplotter to
configure and control the autopilot system.
1
Determine where to connect the CCU
(optional)
to your existing NMEA 2000 backbone
2
In the location where you plan to connect the CCU,
disconnect one side of a NMEA 2000 T-connector
network.
3
If necessary, connect a NMEA 2000 backbone extension
cable (not included) to the side of the disconnected T-
connector to extend the NMEA 2000 network backbone.
4
Add an included T‑connector for the CCU to the NMEA 2000
backbone by connecting it to the side of the disconnected
T‑connector or backbone extension cable.
5
Route the included drop cable
bottom of the T-connector added in step 4.
If the included drop cable is not long enough, you can use a
drop cable up to 6 m (20 ft.) long (not included).
6
Connect the drop cable to the CCU and the T-connector.
7
If needed, repeat steps 2 through 6 for the helm control
(optional) or a compatible Garmin chartplotter.
Connecting Optional NMEA 2000 Devices to the
Autopilot System
You can use advanced features of the autopilot system by
connecting optional NMEA 2000 compatible devices, such as a
GPS device, to the NMEA 2000 network.
6
to
.
.
to each end of
and the helm control
.
from the
to the CCU and to the
NOTE: You can connect optional devices that are not NMEA
2000 compatible to the helm control through NMEA 0183
(NMEA 0183 Connection Considerations, page
1
Add an additional T-connector (not included) to the NMEA
2000 network.
2
Connect the optional NMEA 2000 device to the T-connector
by following the instructions provided with the device.
Bleeding the Hydraulics
This is a general procedure for bleeding a hydraulic steering
system. Refer to the instructions provided by the manufacturer
of the steering system for more-specific information about
bleeding the system.
Before you bleed the hydraulic system, you should verify that all
hose connections are complete and fully tightened.
1
Select an option:
• If the helm reservoir contains insufficient fluid, fill it as
needed.
• If the helm reservoir contains excess fluid, remove the
excess to avoid fluid overflow during the bleeding process.
2
Insert a bypass hose between the cylinder bleed ports.
TIP: If you use a clear plastic hose for this bypass, you can
observe air bubbles during the bleeding processes.
3
Manually steer the helm fully to port.
4
Open both bypass valves at the cylinder fittings.
5
Manually turn the helm slowly to port over three minutes.
TIP: You can stop turning when you no longer see air moving
through the bypass hose.
6
Turn on the autopilot system and disable the Shadow Drive.
You can refer to the autopilot system documentation for more
information on disabling the Shadow Drive.
7
Hold
(port) on the helm control for at least 10 seconds.
TIP: You can stop holding
moving through the bypass hose.
8
Close both bypass valves at the cylinder fittings.
9
If necessary, add fluid to the helm reservoir.
10
Repeat steps 3 through 9 for the starboard side.
11
Hold
(port) on the helm control until steering stops and
Hydraulic Pump Stall is shown on the helm control.
12
Hold
(starboard) on the helm control until steering stops
and Hydraulic Pump Stall is shown on the helm control.
13
Select an option:
• If Hydraulic Pump Stall is not shown within 2 to 3
seconds after the cylinder stops, repeat steps 1-13 to
bleed the system again.
• If Hydraulic Pump Stall is shown within 2 to 3 seconds
after the cylinder stops, the system bleed completed
successfully.
After hydraulic bleeding is complete, you can re-enable the
Shadow Drive.
Corrosion Blocker
To ensure the long life of all parts, apply corrosion blocker to the
pump at least twice yearly.
A marine-rated corrosion blocker should be applied to the pump
after all hydraulic and electrical connections are made and the
hydraulic system has been bled.
Configuration
The autopilot must be configured and tuned to your boat
dynamics. You can use the Dockside Wizard and the Sea Trial
7).
NOTICE
when you no longer see air
NOTICE