Garmin Sport PRO Manual do Proprietário - Página 7

Procurar online ou descarregar pdf Manual do Proprietário para Produtos para animais de estimação Garmin Sport PRO. Garmin Sport PRO 12 páginas. Dog collar device gps
Também para Garmin Sport PRO: Manual do Proprietário (20 páginas)

Imprimir página

Select the correct contact point length for your dog's coat

type:

• For dogs with thicker coats, use the longer contact points.

• For dogs with shorter coats, use the shorter contact

points.

If necessary, use the included wrench to remove the contact

points.

Twist the contact points into the collar.

Tighten with the included wrench, but do not overtighten.

When you put the collar on the dog, make sure the contact

points are tight against the neck.

Dog Training

You should research and investigate the training methods best

suited for you, your dog, and your needs.

When used properly, the Sport PRO training system is an

effective training tool to aid your dog in reaching its full potential.

The use of the training system should be part of an overall

training program.

Training Methods

Momentary stimulation: Applies a brief stimulation when you

press the training key, regardless of how long the key is

depressed.

Continuous stimulation: Applies stimulation to the dog the

entire time you press the training key, for a maximum of 8

seconds. Your stimulations should typically be much shorter

than 8 seconds.

Tone: Activates an audible tone instead of stimulation. A tone

can be used as either a positive or negative training cue,

depending on your training program.

Vibration: Applies vibration instead of stimulation to the dog the

entire time you press the training key, for a maximum of 8

seconds. The effectiveness of vibration may vary based on

the dog's temperament and experience.

Choosing the Correct Intensity Level

Set the intensity to the lowest level.

Select a training key.

Observe the dog for a reaction, such as a head shake, neck

movement, or just a change in expression.

Sometimes dogs will vocalize due to the surprise of the

electrical stimulation. If the dog vocalizes more than once,

the intensity level is too high for beginning training.

If there is no reaction, increase the intensity level by one level

until the dog has a slight but recognizable reaction to the

stimulation.

The intensity level that causes a slight but recognizable reaction

is your dog's baseline level for beginning collar training. You do

not need to, and should not, apply this intensity selection test

again.

After you begin training, the dog's performance guides your

intensity selection. As the dog advances in training, you may

need to change the level depending upon the training situation.

Changing the Intensity Level

You can select a different intensity level for each dog collar

device.

Select a dog collar device

page

2).

Adjust the dial to increase or decrease the intensity level.

Dog Training

(Selecting a Dog Collar Device,

BarkLimiter

Before playing with your dog, you should remove the dog collar

device or deactivate the BarkLimiter feature.

When using the BarkLimiter feature, you should remove all other

collars, tags, or other items from your dog. These other items

can cause the BarkLimiter feature to activate when the dog is

not barking.

The BarkLimiter feature can correct your dog automatically

when the dog barks. The device detects vibrations to distinguish

between barking and other vocalizations. You can use these

methods when correcting your dog with the BarkLimiter feature.

• Vibration instead of stimulation

• Fixed stimulation

• An automatic, gradual increase in stimulation intensity

Automatic Intensity

The device can set the stimulation intensity level automatically

based on the barking behavior of the dog. The device starts at

the lowest intensity level and increases the intensity level

gradually until the dog stops barking. When the dog is quiet, the

intensity decreases over time.

The automatic intensity feature is designed to eliminate

excessive nuisance barking. To stop barks more immediately,

you should set the intensity level manually.

Status LED

The status LED flashes briefly when the dog collar device

detects motion or corrects a bark.

Green, yellow, or red

Motion was detected, and no correction was

flash

applied.

Blue flash

A bark was detected, and a correction was

applied.

NOTE: A green, yellow, or red flash denotes how much charge

is left in the dog device battery, ranging from high to low.

Enabling the BarkLimiter Feature from the Handheld

Device

You can use your handheld device to enable BarkLimiter

features. When you enable BarkLimiter mode from the handheld

device, you can set the dog collar device to use auto-rise,

vibration, or fixed stimulation levels.

Set the operating mode dial to AUX.

Select BARKLIMITER ON.

The green LED flashes.

While the green LED is flashing, select an option:

• To set vibration, select VIBE.

• To set a fixed stimulation level, set the dial to a stimulation

level and select CONTINUOUS.

• To set auto-rise, select BARKLIMITER ON.

A blue LED on the dog collar device indicates that it is in

BarkLimiter mode.

Turning Off the BarkLimiter Feature from the Handheld

Device

NOTE: If you enabled the BarkLimiter feature from the dog

device, you cannot turn it off from the handheld device.

Set the dial to AUX.

Select BARKLIMITER OFF.

Overriding the BarkLimiter Feature

NOTE: If you enabled the BarkLimiter feature from the dog

collar device, you cannot override it using the handheld device.

If you need to apply a quick stimulation when your dog collar

device is in BarkLimiter mode, you can override the BarkLimiter

feature using the handheld device. You can return to BarkLimiter

NOTICE