Fujitsu UTY-RNRUZ2 Manual de instalação - Página 9

Procurar online ou descarregar pdf Manual de instalação para Ar condicionado Fujitsu UTY-RNRUZ2. Fujitsu UTY-RNRUZ2 11 páginas. Remote controller (wired type)
Também para Fujitsu UTY-RNRUZ2: Manual de instruções (26 páginas)

Imprimir página
Fujitsu UTY-RNRUZ2 Manual de instalação
6.4.4. Version
1.
Touch the [Version] on the "Maintenance"
screen. The "Version" screen is displayed.
Touch [Back] to return to the "Maintenance"
screen.
6.4.5. Test Run
Carry out a test run after completing configuration.
1.
Touch the [Test Run] on the "Maintenance"
screen. The "Test Run" screen is dis-
played.
Touch [OK] to return to the "Maintenance"
screen, and start the test run. The test run
will automatically end in approximately 60
min.
When test run is ended midway, return to the "Monitor Mode" screen
and check the occupied state. When "Occupied" is displayed, press the
operation button to set to "Unoccupied". Then test run is ended. When
"Unoccupied" is displayed, press the operation button once to set to
"Occupied" and press it again to set to "Unoccupied". Then test run is
ended.
6.4.6. R.C. Address Setting
Addresses will be automatically set when initially starting up this unit. In
such a case, do not change the remote controller address for the indoor
unit, and keep it at the initial setting of 0.
• Checking the remote controller address
1.
Touch the [R.C. Address Setting] on the
"Maintenance" screen. The "R.C. Address
Setting" screen is displayed.
The "Current Address" is displayed as
[System-Unit]. The value for "Unit" refers
to the remote controller address.
Touch [Back] to return to the "Maintenance" screen.
When the address is set manually, this
mark is displayed.
• Manual Address Setting
Only set addresses manually when using different numbers for
addresses.
A remote-controller address for the indoor unit needs to be set.
Set the remote-control addresses for the indoor units which are
connected using the same remote-control cable with a range from 1 to
9 and from A (10) to F(15), without any duplicates. (Do not use "0" for
configuration.)
For how to configure the remote control addresses for the indoor unit,
refer to its work manual.
1.
Touch the [RC Address Setting] on the "Maintenance" screen. The
"R.C. Address Setting" screen is displayed.
Touch the [Manual Addressing]. The "Manual Addressing" screen is
displayed.
2.
Touch [ ] or [ ] to set the addresses of this unit. Touch [OK] to
display the confirmation screen, and touch [Yes] to return to the RC
Address setting screen.
If you wish to carry out configuration again, touch [Address Reset]
on the "R.C. Address Setting".
1.
2.
R.C.Address Setting
Manual Addressing
System
Current Address
[001–01]
Manual Addressing
001
Address Reset
Back
Cancel
The address for this unit can be set from 1 to 32. However, do not set
the same number as that for the remote-control address of an indoor
unit connected using the same remote-control cable.
Version
E000V00P00L00
Back

Test Run

The test run will be performed. OK?
Cancel
OK
R.C.Address Setting
Current Address
[001–01]
Manual Addressing
Address Reset
Back
Unit
01
OK
6.4.7. I.U. Address Verification
Check the address and position of the indoor unit.
1.
Touch the [I.U. Address Verification] on the "Maintenance" screen.
The "I.U. Address Verification" screen is displayed.
If there are multiple pages, you can switch between them by touch-
ing [Next Page] or [Previous Page].
Touch [Check] to display the indoor unit address checking start
screen.
2.
Touch [Yes] to display the confirmation screen.
3.
Select the indoor unit to be checked. If there are multiple pages,
you can switch between them by touching [Next Page] or [Previ-
ous Page]. The selected indoor unit will start to blow air and flash a
LED*. (*Only when the indoor unit has the relevant functions)
Touch [Back] on the confirmation screen to return to the previous
screen.
1.
2.

I.U. Address Verification

Page 1/ 2
I.U. Address Verification
No. System–Unit
/
Ref.–In.
1 002–01
/
01–01
2
002–02
/
01–02
3
002–03
/
01–03
Indoor unit position will be checked. OK?
4
002–04
/
01–04
5
002–05
/
01–05
6
002–06
/
01–06
Next
Back
Check
No
Page
4.
Touch [Back] on the "IU Address Verifica-
tion" Screen to return to the "Maintenance"
Screen.
6.4.8. Function Setting
This procedure changes the function settings used to control the indoor
unit according to the installation conditions. Incorrect settings can cause
the indoor unit to malfunction. Perform the "Function Setting" according to
the installation conditions using the remote controller.
• Refer to the indoor unit installation manual for details on the function
numbers and setting numbers, before the start of function setting.
1.
Touch the [Function Setting] on the "Maintenance" screen. The
"Function Setting" screen is displayed.
Touch the [Address] on the "Function Setting" screen. The "Address"
screen is displayed.
2.
Touch [ ] or [ ] to select the address of the indoor units to be con-
figured. (To set all indoor units at the same time, touch [All].) Touch
[OK] to return to the Function Setting screen.
3.
Touch the [Function No.] on the "Function Setting" screen. The
"Function No." screen is displayed.
1.
2.

Function Setting

Address
Address
[002–01]
002–01
Function No.
[00]
Setting No.
[00]
Back
Setting
Cancel
4.
Touch [ ] or [ ] to set the function number. Touch [OK] to return to
the "Function Setting" screen.
5.
Touch the [Setting No.] on the "Function Setting" screen. The "Set-
ting No." screen is displayed.
6.
Touch [ ] or [ ] to set the setting number. Touch [OK] to return to
the "Function Setting" screen.
4.
5.
Function No.
Function Setting
Address
00
Function No.
Setting No.
Cancel
OK
Back
7.
Touch [Back] to return to the "Maintenance"
screen.
3.
I.U. Address Verification
Page 1/ 2
No. System–Unit
/
Ref.–In.
1 002–01
/
01–01
2 002–02
/
01–02
3 002–03
/
01–03
Next
Yes
End
Page
I.U. Address Verification
Page 1/ 2
No. System–Unit
/
Ref.–In.
1 002–01
/
01–01
2
002–02
/
01–02
3
002–03
/
01–03
4
002–04
/
01–04
5
002–05
/
01–05
6
002–06
/
01–06
Next
Back
Check
Page
3.
Function Setting
All
Address
[002–01]
Function No.
[00]
Setting No.
[00]
OK
Back
Setting
6.
Function Setting
Address
[002–01]
[002–01]
Function No.
[00]
Setting No.
[00]
00
[00]
Setting
Cancel
OK
Function Setting
Address
[002–01]
Function No.
[00]
Setting No.
[00]
Back
Setting
En-9