Indesit DIF 04B1 Manual de Instruções - Página 13

Procurar online ou descarregar pdf Manual de Instruções para Máquina de lavar loiça Indesit DIF 04B1. Indesit DIF 04B1 20 páginas.
Também para Indesit DIF 04B1: Manual de Instruções (20 páginas)

Imprimir página

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table/industrial salt or washing-up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

any rinse aid. However, we recommend that you add salt,

especially if you live in an area where the water is hard or

(Follow the instructions given on the packaging).

very hard.

If you do not add salt or rinse aid, the LOW SALT

LOW RINSE AID

indicator lights will stay lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs off

the surfaces more readily and therefore does not leave streaks

or marks. The rinse aid dispenser should be filled:

• When the LOW RINSE AID indicator light

is illuminated, a reserve supply of rinse aid is still available

for 1-2 cycles;

"D"

1. Open the dispenser

by pressing and pulling up the tab

on the lid;

2. Carefully introduce the rinse aid as far as the maximum

reference notch of the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

can adjust the quantity of rinse aid.

Switch the dishwasher on and off using the On/Off button. Press

the P button 3 times. Switch on using the ON/OFF button, the

indicator light of the set level flashes (set to factory level)

Adjust the level of rinse aid supply using the P button; during

this procedure the rinse aid indicator light flashes.

Press the ON/OFF button to save the setting.

If the rinse aid level is set to ZERO (ECO cycle), no rinse aid will

be supplied. The LOW RINSE AID indicator light will not be lit if

you run out of rinse aid.

Up to maximum 4 levels can be set based on the dishwasher

model.

• If there are streaks on the crockery, set to a low number (1-2).

• I n case of drops of water or limescale marks, set to a high

number number (3-4).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt specially designed for this type of appliance,

supplies water without limescale which is then used to wash

the crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the

water hardness level in your area. This information can be

obtained from your local water supplier.

Switch the dishwasher on and off using the ON/OFF button.

Press and hold the P button for a few seconds until you hear

a beep sound. Switch the dishwasher on using the ON/OFF

button, the indicator light of the set level flashes

set to medium

During this procedure the salt indicator light flashes.

Adjust the hardness level using the P button,

hardness table)

Press the ON/OFF button to save the setting.

and

Even if using multi-functional tablets, the salt dispenser should

still be filled.

Water Hardness Table

level

on the control panel

For values between 0°f and 10°f, we do not recommend the use of salt.

cycles.

(°dH = hardness measured in German degrees - °f = hardness

measured in French degrees – mmol/l = millimoles per litre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the salt dispenser is never empty.

Refined salt removes limescale from the water, thus avoiding

the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

tank right up to its edge.

3. Position the funnel

to the edge (approximately 1 kg). It is normal for a little water

to leak out.

4. Remove the funnel* and wipe any salt residues away from

the opening; rinse the cap under running water and then screw

it on, the head facing downwards so as to let the water flow out

of the four slots (star-shaped arrangement) in the lower part of

the cap (cap with green float

It is advisable to perform this procedure every time you add

salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

so that any saline solution which has leaked out of the salt

dispenser is removed.

Only available in selected models.

level).

up to max. 4

levels.

°dH

°fH

mmol/l

0 - 11

0 - 20

1,1 - 2

12 - 17

21 - 30

2,1 - 3

17 - 34

31 - 60

3,1 - 6

34 - 50

61 - 90

6,1 - 9

this setting may cause a slight increase in the duration of the

for 1 wash cycle per day.

and should be filled:

•

When the green float

seen by simply looking at the cap of the

salt dispenser;

•

When the LOW RINSE AID indicator

light on the control panel is illuminated

1. Remove the lower rack and unscrew

the cap (anticlockwise).

2. The first time you do this: fill the water

(see figure)

When necessary, measure out the salt before a wash cycle

(water softener

(1-2-3-4

see water

Average salt container

capacity duration

months

5 months

3 months

2 months

2/3 weeks

cannot be

;

and fill the salt dispenser up