Indesit ID50G Manual de Instruções - Página 5

Procurar online ou descarregar pdf Manual de Instruções para Fogões Indesit ID50G. Indesit ID50G 24 páginas. 50cm free standing gas cooker

Imprimir página

only after it is ascertained that it is adaptable to the type of

gas to be used. If not, follow the instructions indicated in

the paragraph headed "Adaptation to diff erent gas types".

On some models the gas supply can be connected on the

left or on the right, as necessary; to change the connection,

reverse the position of the hose holder with that of the cap

and replace the gasket (supplied with the appliance). In

the case of connection to liquid gas, by tank, use pressure

regulators that conform to the regulation in force. The gas

supply must be connected to the left of the appliance. Be

sure that the hose does not pass through the rear of the

cooker touching hot parts.

! make sure the supply pressure conforms with the

values shown in the table entitled "Caracteristics of

the burners and nozzles". When the cooker is installed

between cabinets (recessed), the gas connection must be

eff ected by an approved fl exible hose with bayonet fi tting

(BS 669 Current Edition). The gas inlet for the cookers is a

threaded G 1/2 gas female fi tting.

Connecting the gas supply

To make the connection, a fl exible hose should be used

corresponding to the current gas regulations which are:

• the hose must never be at any point in its lenght in

contact with the "hot" parts of the cooker;

• the hose must never be longer than 1,5 metre;

• the hose must not be subject to any tension or torsional

stress and it must not have any excessively narrow

curves or bottlenecks;

• the hose must be easy to inspect along its entire length

to check its condition;

• the hose must always be in good condition, never

attempt to repair.

! the installation must comply

with gas safety (installation and

HOT PARTS

use) regulations 1984. In all cases

for the above, by low, a qualifi ed,

gas sa e approved engineer must be

called for installation.

Electrical connection

Power supply voltage and frequency: 230-240V a.c. 50Hz.

! the supply cable must be positioned so that it never

reaches at any point a temperature 50°C higher than

the room temperature. The cable must be routed away

from the rear vents. Should you require it, you may use

a longer cable, however, you must ensure that the cable

supplied with the appliance is replaced by one of the same

specifi cations in accordance with current standards and

legislation.

Your appliance is supplied with a 13 amp fused plug that

can be plugged into a 13 amp socket for immediate use.

Before using the appliance please read the instructions

below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT

BY A QUALIFIED ELECTRICIAN.

Replacing the fuse

When replacing a faulty fuse, a 13 amp ASTA approved

fuse to BS 1362 should always be used, and the fuse cover

re-fi tted. If the fuse cover is lost, the plug must not be used

until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fi tted, it must be of the

correct colour as indicated by the coloured marking or the

colour that is embossed in words on the base of the plug.

Replacements can be obtained directly from your nearest

Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug and

you should wish to remove it to add a cable extension or

to re-route the mains cable through partitions, units etc.,

please ensure that either:

• the plug is replaced by a fused 13 amp re-wireable plug

bearing the BSI mark of approval.

or:

• the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with BS

5733) which is accessible without moving the appliance.

Please note: for appliances with a rating greater than 13

amp (eg: electric hob, double ovens and freestanding

electric cookers etc.) the mains cable must be wired into a

cooker output point with a rating of 45 amp. In this case the

cable is not supplied.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make

the pins unusable so that it cannot be accidentally inserted

into a socket. Instructions for connecting cable to an

alternative plug:

! the wires in the mains lead are coloured in accordance

with the following code:

Green & Yellow

- Earth

Blue

- Neutral

Brown

- Live

If the colours of the wires in the mains lead do not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked "E" or

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked "L" or coloured Red.