Indesit KG 6408 WV/G Manual de instruções de instalação e utilização - Página 4
Procurar online ou descarregar pdf Manual de instruções de instalação e utilização para Fogões Indesit KG 6408 WV/G. Indesit KG 6408 WV/G 12 páginas. Indesit cooker with ventilated oven instructions for installation and use
Imprimir página
Electrical Connection
Your appliance is now supplied with a 13 amp fused plug
that can be plugged into a 13 amp socket for immediate use.
Before using the appliance please read the instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED
OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved fuse
to BS 1362 should always be used, and the fuse cover re-
fitted. If the fuse cover is lost, the plug must not be used until
a replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colour as indicated by the coloured marking or the colour
that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug and
you should wish to remove it to add a cable extension or to
re-route the mains cable through partitions, units etc., please
ensure that either:
-
the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
or:
-
the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
Please note: for appliances with a rating greater than 13
amp (eg: electric hob, double ovens and freestanding electric
cookers etc.) the mains cable must be wired into a cooker
output point with a rating of 45 amp. In this case the cable is
not supplied.
Disposing of the plug:
Ensure that before disposing of the plug itself, you make the
pins unusable so that it cannot be accidentally inserted into
a socket.
The cooker is supplied adjusted for natural gas
(methane).
To adapt the cooker to a type of gas which is different
from the one it was designed for the following operations
must be carried out:
Important: disconnect the cooker from the electricity.
1) Replacement of nozzles and regulating air.
a) Upper burners
Remove grids, flame separator plates and burners from
·
the hob.
Loosen screws "A" (see Fig. A) remove bushes from
·
work top and lift the latter up.
Loosen screws "B" and lift the pipe "C" (Fig. B).
·
Unscrew the nozzles and replace them (see Fig. B)
·
with those suitable for the new gas as supplied with
the cooker in accordance with table 2.
Adaptation to the different types of gas
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
- Earth
Blue
- Neutral
Brown
- Live
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked "E" or
or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked "L" or coloured Red.
Connect Blue wire to terminal marked "N" or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a 13
amp fuse. A 15 amp plug must be protected by a 15 amp
fuse, either in the plug or adaptor or at the distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with
the following code:
GREEN &
YELLOW
BROWN
BLUE
BLUE
BROWN
GREEN AND YELLOW
Disposing of the appliance:
When disposing of the appliance please remove the plug by
cutting the mains cable as close as possible to the plug body
and dispose of it as described above.
To regulate the amount of air to the burner, adjust hose
·
"C" according to the values indicated in table 1, "Air
Regulation for Burners". Once the adjustment is made,
fix hose "C" with the screw "B" (Fig. B).
2)
Regulation of minimums
When installing the cooker make sure that the minimums
of all upper burners are duly regulated. Regulation of
minimums is essential when changing the type of gas.
Proceed as follows:
•
Taking one burner at a time, switch on to the maximum
position, remove the knob, inser t the special
screwdriver into the hole of the tap "T" rod and slightly
unscrew to regulate the minimum. If the tap rod hasn't
the hole insert a screwdriver into the hole of the facia
panel and slightly unscrew "S" screw to regulate the
minimum (Fig. A).
•
Then turn the tap to minimum position.
4
13 amp fuse
CROSS-BAR
CORD GRIP
"NEUTRAL" ("N")
"LIVE" ("L")
"EARTH" ("E")