Indesit 7HKEC 647 X RU/HA Manual de Instruções - Página 3

Procurar online ou descarregar pdf Manual de Instruções para Hob Indesit 7HKEC 647 X RU/HA. Indesit 7HKEC 647 X RU/HA 24 páginas.

Imprimir página

1. Control Panel

Fixing

The appliance must be installed

supporting surface.

Any deformities caused by improper fixing could affect the

features and operation of the hob.

The thickness of the supporting surface

the length of the screws for the

account when choosing

fixing hooks:

• 30 mm thick: 23 mm screws

• 40 mm thick: 13 mm screws

Fix the hob as follows:

1. Use short flat-bottomed screws to fix the 4 alignment

springs in the holes provided at the central point of each

side of the hob.

2. Place the hob in the cavity, make sure it is in a central

position and push down on the whole perimeter until the

hob is stuck to the supporting surface.

3. For hobs with raised sides: After inserting the hob into

its cavity, insert the 4 fixing hooks (each has its own pin)

into the lower edges of the hob, using the long pointed

screws to fix them in place, until the glass is stuck to the

supporting surface.

The screws for the alignment springs must remain

accessible.

In order to adhere to safety standards, the appliance

must not come into contact with electrical parts once it has

been installed.

All parts which ensure the safe operation of the appliance

must not be removable without the aid of a tool.

Electrical connection

The electrical connection for the hob and for any built-in

oven must be carried out separately, both for safety

purposes and to make extracting the oven easier.

Single-phase connection

The hob is equipped with a pre-connected electricity

supply cable, which is designed for single-phase

connection. Connect the wires in accordance with the

instructions given in the following table and diagrams:

Voltage and

Electrical cable

mains frequency

220-240V 1+N ~

50 Hz

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

• 400V - 2+N ~ 50 Hz

• 220-240V 3 ~ 50 Hz

on a perfectly level

should be taken into

Wire connection

: yellow/green

: the two blue wires together

: brown and black together

• 400V 3 - N ~ 50 Hz

• 400V - 2+2N ~ 50 Hz

Separate the wires and connect them in accordance with

the instructions given in the following table and diagrams:

Voltage and

Electrical cable

mains frequency

400V - 2+N ~

50 Hz

220-240V 3 ~

50 Hz

400V 3-N ~

50 Hz

400V - 2+2N ~

50 Hz

Connecting the electricity supply cable to the mains

If the appliance is being connected directly to the

electricity mains an omnipolar switch must be installed with

a minimum opening of 3 mm between contacts.

The installer must ensure that the correct electrical

connection has been made and that it is fully compliant

with safety regulations.

Before connecting the appliance to the power supply,

make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate located

on the appliance itself.

• The voltage falls within the range of values indicated on

the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

The cable must not be bent or compressed.

The cable must be checked regularly and replaced by

authorised technicians only.

The manufacturer declines any liability should these

safety measures not be observed.

Do not remove or replace the power supply cable for any

reason. Its removal or replacement will void the warranty

and the CE marking. INDESIT does not assume liability for

accidents or damage arising from replacement/removal of

the original power supply cable. Replacement can only be

accepted when carried out by personnel authorised by

INDESIT and using an original spare part.

Wire connection

: yellow/green;

N: the two blue wires

together

L1: black

L2: brown

: yellow/green;

N1: blue

N2: blue

L1: black

L2: brown