Indesit F159214 Manual de instruções de utilização - Página 6
Procurar online ou descarregar pdf Manual de instruções de utilização para Hob Indesit F159214. Indesit F159214 10 páginas.
Imprimir página
ACCESSORIES
POTS AND PANS
Only use pots and pans made from ferromagnetic
OK
NO
material which are suitable for use with induction hobs:
• enamelled steel
• cast iron
• special pots and pans in stainless steel, suitable
for induction cooking
To determine whether a pot is suitable, check for the
stamped on the bottom). A magnet may be used to check whether pots are
magnetic.
The quality and the structure of the pot base can alter cooking performance.
Some indications for the diameter of the base do not correspond to the
actual diameter of the ferromagnetic surface.
Some pots and pans have only a part of the bottom in ferromagnetic
material, with parts in another material that is not suitable for induction
cooking. These areas may heat up at different levels or with lower
temperatures. In certain cases, where the bottom is made mainly of
non-ferromagnetic materials, the hob might not recognise the pan and
therefore not switch on the cooking zone.
To ensure optimum efficiency, always use pots and pans with a flat bottom
that distributes the heat evenly. If the bottom is uneven, this will affect
power and heat conduction.
FIRST TIME USE
POWER MANAGEMENT
At the time of purchase, the hob is set to the maximum possible power.
Adjust the setting in relation to the limits of the electrical system in your
home as described in the following paragraph.
N.B: Depending on the power selected for the hob, some of the cooking
zone power levels and functions (e.g. boil or quick reheating) could be
automatically limited, in order to prevent the selected limit from being
exceeded.
To set the power of the hob:
Once you have connected the device to the mains power supply, you can
set the power level within 60 seconds.
Press the "+" button for at least 3 seconds. The display shows "PL".
Press the
button to confirm.
Use the "+" and "−" buttons to select the desired power level.
The power levels available are: 2,5 kW – 3,7 kW.
Confirm by pressing
.
The power level selected will stay in the memory even if the power supply
is interrupted.
To change the power level, disconnect the appliance from the mains for at
least 60 seconds, then plug it back in and repeat the steps above.
Empty pots or pots with a thin base
Do not use empty pots or pans when the hob is on. The hob is equipped with
an internal safety system that constantly monitors the temperature, activating
the "automatic off" function where high temperatures are detected. When
used with empty pots or pots with thin bases, the temperature may rise very
quickly, and the "automatic off" function may not be triggered immediately,
damaging the pan or the hob surface. If this occurs, do not touch anything,
and wait for all components to cool down.
symbol (usually
If any error messages appear, call the service centre.
Minimum diameter of pot/pan base for the different cooking areas
To ensure that the hob functions properly, use pots of a suitable minimum
diameter (refer to the drawing below).
Always use the cooking zone that best corresponds to the minimum
diameter of the bottom of the pot.
Place the pot making sure it is well centered on the cooking zone in use.
It is recommended not to use pots that exceed the perimeter of the cooking
zone in use.
ADAPTER FOR POTS/PANS UNSUITABLE FOR INDUCTION
Using this accessory makes it possible to use pots and pans that are not
suitable for induction hobs. It is important to bear in mind that using it
affects efficiency and consequently the time needed to heat food. Its
use should be limited because the temperatures reached on its surface
depend significantly on the pot/pan used, its flatness and the type of food
being cooked. Using a pot or pan with a smaller diameter than the adapter
disc may cause heat to build up that is not transmitted to the pot or pan
and this could blacken both the hob and the disc. Adapt the diameter of
your pots/pans and the hob to the diameter of the adapter.
If an error occurs during the setting sequence, the "EE" symbol will appear,
and you will hear a beep. If this happens, repeat the operation.
If the error persists, contact the After-Sales Service.
ACOUSTIC SIGNAL ON/OFF
To switch the acoustic signal on/off:
•
Connect the hob to the power supply;
•
Wait for the switch-on sequence;
•
Within 60 seconds, press the buttons "+" and
at least 5 seconds.
DEMO MODE (reheating deactivated, see section on "Troubleshooting")
To switch the demo mode on and off:
•
Connect the hob to the power supply;
•
Wait for the switch-on sequence;
•
Within 60 seconds, simultaneously press the left-hand cooking zone
selection buttons for at least 3 seconds (as shown below);
•
"DE" will show on the display.
ø min.
150 mm
ø min.
100 mm
3 sec.
simultaneously for