Kohler URBANITY 23748T-9 Instruções de instalação - Página 4

Procurar online ou descarregar pdf Instruções de instalação para Produto de canalização Kohler URBANITY 23748T-9. Kohler URBANITY 23748T-9 4 páginas. Wall mount thermostatic bath & shower faucet, wall mount thermostatic shower only faucet

Imprimir página

INSTALLATION

Cold

Hot

C-ring

Cold

Hot

Opening

downward

Screw

Protector cap

1387023-2A-A

Install the Body

To perform installation, installer must provide G1/2" female supply

fittings(1), spaced 150mm apart, horizontally and vertically to the

finished flat wall. Flush the water supply pipes thoroughly to

remove any debris.

NOTE: Apply water pressure test on water supply pipes before

installing the connectors(2).

Apply enough tape or suitable sealant on threads of connectors.

Install two connectors into the hot and cold supply pipes.

Adjust the center-to-center distance between the connectors to

150mm horizontally. They should extend 36~45mm beyond the

finished wall. NOTE: Rotate the C-rings with their openings

downward, and pull forward the C-rings to clamp the connectors.

Adjust two screws(4) with 3mm hex wrench(3). Install the faucet

body to the connectors until it is against the finished wall. Ensure

the upper surface is horizontal with the level(5).

Tighten two screws with 3mm hex wrench(The screws should

contact with the connectors through the C-rings' openings).

Press the plugs(6) into the faucet.

Install the Handshower

Remove the protector cap from the connector(7)．

Put the screen washer(8) into the shower hose(9). Connect the

handshower(10) and connector(7) with shower hose. Tighten all

the connectors. NOTE: Don't over tighten.

Install the check valve(11) into the handshower if needed.

Drain notch

INSTALLATION CHECKOUT

Indicator line

Upward

horizontally

Spindle

CARE AND MAINTENANCE

Filter

1387023-2A-A

Install the Bracket

Determine a suitable location on the finished wall to install bracket.

Ensure it should avoid buried cables and pipes in the wall.

Mark the mounting holes of the base(12) on the wall according to

the dimension. Drill two holes in the finished wall, the holes should

match the anchors(13) and be vertical. Install the anchors. Tighten

the screws(14) to fix the base on the finished wall. NOTE: The

direction of the base is shown in the figure.

Loosen the screw(17) in the bracket(16) bottom with hex wrench

(15) until the bracket can be installed into the base. Slide the

escutcheon(18) onto the bracket. Apply a ring of plumbers putty or

other sealants around the underside of the escutcheon. Move the

bracket onto the base until it is against the finished wall and

confirm the drain notch and screw hole are pointed down. Tighten

the screw(17) with hex wrench to fix the bracket and escutcheon

on the finished wall. Remove any excess putty or sealant.

Ensure that all connections are tight, the switch buttons are not

turned on. Turn on the water supply. Run water through the valve.

Check for leakage. Repair as needed.

Press the buttons separately. Check whether all connections and

water flow are well. Shut off the faucet.

Verification and Setting

Make sure that the water feeds of the faucet have reach their

highest temperature by letting the water run sufficiently. When the

number 37 on the temperature handle(19) is upward vertically,

the temperature of the water coming out of the faucet must be

Number 37

within a range of 36ºC and 38ºC, as measured by a thermometer.

If this is not the case, the installer can adjust the setting. Proceed

with the setting as follows:

Remove the plug(21). Take out the screw(20) with 2.5mm hex

wrench(22) to uninstall the temperature handle(19). Remove the

screw(23) with a screwdriver. Remove the adapter spline(24).

With the faucet on "cold" normal water flow, slowly turn the

temperature selector(Always in the same direction) until water is

at 37ºC. If the temperature goes over 37ºC, go back to the "cold"

setting and set again. When the temperature is stabilized, do not

turn the cartridge spindle. Install the adapter spline. Ensure the

indicator line on the adapter spline align with the indicator line on

the stopper. Tighten the screw(23) with a screwdriver. Install the

temperature handle. Ensure the number 37 on the temperature

handle is upward vertically(After assembly, it could not be turned

counter-clockwise if not pushing the button). Tighten the screw

(20) with 2.5mm hex wrench. Insert the plug(21).

Clear the Filter

The filters protecting the faucet device may get obstructed and

reduce water flow. When this happens, turn off the water supply,

uninstall the shower column.

Take out the plugs(6). Unscrew two screws(4) with 3mm hex

wrench(3) to uninstall faucet. Take out the filters by hand. Clean

the filters by soaking them in warm vinegar. Reinstall in turn.