2VV AirGENIO Manual de instalação, operação e manutenção - Página 9
Procurar online ou descarregar pdf Manual de instalação, operação e manutenção para Sistemas de controlo 2VV AirGENIO. 2VV AirGENIO 20 páginas. Finesse ec/standesse ec superior controls
Também para 2VV AirGENIO: Instruções de montagem, instalação e funcionamento (11 páginas)
Imprimir página
ACCESSORIES
CONNECTING EXTERNAL ACCESSORIES
PLEASE NOTE
The unit must be disconnected from the power supply to connect accessories.
•
All external control components must be connected according to the wiring diagram.
•
The connectors must be connected to the electrical board with adequate force and always perpendicular to the base.
•
DS door contact
TECHNICAL INFORMATION
• Isolated switching contact with maximum voltage 230V, 6A
• IP67, can be connected as a break or switching contact
CAUTION!
Not included with the product.
DK-B3 door contact
TECHNICAL INFORMATION
• Isolated switching contact with maximum voltage 12V.
Cable: Two-core cable with a cross section of 0,5 mm
CAUTION!
Not included with the product.
Thermostatic valve – TV1/1
TECHNICAL INFORMATION
• Thermostatic valve to regulate the water exchanger
• Suitable for all types of curtain with water exchanger
• Works independent to the electronic controls
CAUTION!
Not included with the product.
Zone valve ZV-3-24V / ZV-2-24
TECHNICAL INFORMATION
• Zone valve to regulate the water exchanger 0-10V
• Cable: 0.5 mm
Supply 24 V/ 50/60 Hz (24V external source, included), control 0-10V
2
CAUTION!
Not included with the product.
9
"Wiring diagrams" chapter. A suitable cross-section of the
cable shall be determined based on the particular
installation conditions. This cable should be delivered
by a company performing the air curtain electrical
wiring.
Optional accessories
Thermostatic valve
TV1-1/1 (detailed description on the page
399)
Three-way valve with servo drive
ZV-3 (detailed description on the page 395)
Door switch for air curtains fitted with the SM control
DS (detailed description on the page 428)
Door switch for air curtains fitted with
the RF control
(detailed description on the page
DK-1
411)
Mixing point
SMU-xx-xx (detailed description on the
page 390)
WIRING DIAGRAMS
The recommended cross-section of the main power supply
cables is stated in the Instruction Manual.
All wiring diagrams provided in the technical catalog
are indicative only. When assembling the product,
observe strictly the nameplate ratings as well as
Your partner in ventilation...
directions and diagrams affixed directly to the
product or enclosed to the product.
TV1/1
BASIC FEATURES
AIR CURTAINS
The TV1/1 thermostatic valve is designed for controlling the
heat output of water exchangers through throttling. It is
used especially for controlling standalone water-type air
heaters, heaters inbuilt into the ventilation units, heaters in
air curtains, and so on.
Produced in EU
The thermostatic valve shall be installed in sheltered dry
indoor areas with the ambient temperature of +5 °C up to
+60 °C.
Temperature of water being controlled shall range between
0 °C and +90 °C and pressure shall not exceed 0.1 MPa.
The thermostatic valve is designed for controlling the
heating water in accordance with VDI 2035. Water being
controlled shall not contain any solid particles (sand, mud)
or any chemicals.
The thermostatic valve comprises a fitting - DN25 (1") and
thermostatic head with 2 m capillary.
PRIMARY PARAMETERS
2VV. Creating innovative solutions for you and your business since 1995.
118
. - Maximum length: 50 m
2
КРАТКАЯ ХАРАКТЕРИСТИКА
LUFTSCHLEIER
Терморегулирующий клапан TV1/1 предназначен для
регулирования
теплопроизводительности
теплообменников
путем
дросселирования.
зуется, главным образом, для регулирования отдельных
водяных нагревателей воздуха, нагревателей в составе
The company reserves the right of change without previous announce
вентиляционных установок, нагревателей в составе
воздушных завес и т.д.
Терморегулирующий клапан следует устанавливать в
сухих, закрытых помещениях с температурой воздуха от
+5 °C до +60 °C.
Температура воды, проходящей через клапан, должна
быть в пределах от 0 °C до +90 °C, а максимальное
давление 0,1 МПа
Терморегулирующий
клапан
предназначен
регулирования отопительной воды по стандарту VDI
2035. Вода, проходящая через клапан, не должна
содержать твердых частиц (песок, грязь) и каких-либо
химикатов.
Терморегулирующий
клапан
представляет
клапан DN25 (1") с терморегулирующей головкой,
оснащенной капиллярной трубкой длиной 2 м
ГЛАВНЫЕ ПАРАМЕТРЫ
(Steuerungsspannung 230 V) angeschlo
„Elektrische Schaltpläne". Die günstigs
muss laut konkreten Installationsbedin
werden. Dieses Kabel muss die
Luftschleierinstallation anschließt, l
Wählbares Zubehör
Thermostatventil
TV1-1/1 (nähere Beschreibung auf der S
Dreiwegventil mit Servoantrieb
ZV-3 (nähere Beschreibung auf der Seit
Turkontaktschalter fur die mit SM-g
Luftschleiern
DS (nähere Beschreibung auf der Seite 4
Turkontaktschalter fur die mit RF-g
Luftschleiern
DK-1 (nähere Beschreibung auf der Seit
Mischknoten
SMU-xx-xx (nähere Beschreibung auf de
ELEKTRISCHE SCHALTPLÄNE
Empfohlene min. Dimensionierung de
Hauptzuleitung der el. Energie ist
dargestellt.
Sämtliche, im Katalog angeführten,
nur informativ.
richten Sie sich ausschließlich na
werten und Schaltbildern, die ent
Produkt angebracht oder zum Pr
sind.
водяных
Исполь-
для
собой
Bei der Montage