ALLIED MEDICAL KARMA 8520 Manual do utilizador - Página 4
Procurar online ou descarregar pdf Manual do utilizador para Cadeira de rodas ALLIED MEDICAL KARMA 8520. ALLIED MEDICAL KARMA 8520 9 páginas.
2.3.1
Forward Transfer - Getting into the wheelchair
Step 3:
Slide the backcanes up or down to the desired height
As the backcanes are shifted, the back upholstery will move
Remove or swing the legrests to the side.
accordingly. There are a number of holes running vertically through
Lower yourself into the wheelchair using the armrests for support or with the help of
the lower portion of the backcane. These determine how much the
a caregiver.
back height can be raised or lowered.
Refit or swing the legrests back into place, taking care not to catch yourself, and place
CAUTION:
For safety reasons, in the highest position the top two bolts must still
your feet on the legrests.
pass through the square tubing of the frame and the holes running
through the round tubing of the backcane.
2.3.2
Forward Transfer - Getting out of the wheelchair
Step 4:
Replace the top two bolts on both backcanes.
Remove or swing the legrests to one side.
Replace all washers. Tighten each bolt and nut to a point where firm
Move forward in the seat until your feet can reach the floor or you are balanced on
but not crushing the frame.
the edge of the seat.
Place your hands on the front of the armrests and move forwards lifting yourself up
Step 5:
Replace the third lower bolt on both backcanes if they have been
and out of the wheelchair.
removed.
2.3.3
Side Transfer - Getting into the wheelchair
Lift back armrest to clear the seat.
3.6
REMOVING THE SEAT OR BACK UPHOLSTERY
Ensure brake is on.
Remove or swing the legrests to one side.
3.6.1
To remove the back upholstery
Place one hand on the wheelchair seat and ease yourself onto the seat.
2.3.4
Side Transfer - Getting out of the wheelchair
Ensure brake is on.
Remove or swing the footrests to one side.
Remove armrest to clear the seat.
Place one hand on the point of transfer and ease yourself out of the wheelchair.
2.4
OTHER IMPORTANT THINGS YOU SHOULD KNOW
Figure 3.6.1
Step 3:
Slightly fold the wheelchair by putting fingers under the middle of the
Flammability
Do not expose the wheelchair to heat sources e.g. heaters and fires.
seat at both front and rear, grasp and give a sharp pull upwards until
Direct exposure of the wheelchair to a flammable source must be
the wheelchair is nearly closed.
avoided.
Step 4:
Slide the back upholstery off the backcanes.
Resting
Note that the upholstery has been designed for comfort in
general use. Users that are susceptible to pressure sores should also
Step 5:
A tension adjustable or custom back can now be fitted.
use a pressure relief cushion.
Step 6:
Once the new back has been fitted slide rubber grip handles back
onto back canes with a twist and push movement, ensuring they're
placed back in their original position.
Page 9
Page 5
Step 1:
Remove the rubber grip handles. By
slightly heating them with a hairdryer and
twisting them whilst pulling them off, will
make removing of these easier.
Step 2:
Undo the two screws that are located
underneath the rubber grip handles at the
rear of each back cane (see fig. 3.6.1).
3.
MINOR WHEELCHAIR ADJUSTMENTS
3.6.2
To remove the seat upholstery
3.1
ADJUSTING ARMREST HEIGHT
Located on each side of the seat is a row of
Standard flip-back armrest:
screws that securely hold the seat upholstery
in place. This is covered with an extended
The armrest flips back by pressing the release lever located at the front base of the
section of the upholstery and fastened with
armrest. After you press the release lever (fig 3.1.1), you can you lift the armrest
Velcro over the screws to protect the user
backwards.
from damaging their skin.
Step 1:
To remove the seat upholstery, undo the Velcro on the extended
upholstery on each side and undo each screw.
Step 2:
The seat upholstery can now be removed and custom seating can be
fitted.
Step 3:
To replace the seat upholstery, line up the hole in the seat upholstery
Figure 3.1.1
with the holes in the cross bar and replace each screw and washer
and tighten.
To adjust the height of the armrest, simply pull out the silver bolt located underneath
the armrest pad (see fig 3.1.3) and hold onto it whilst adjusting the height of the
3.7
CONVERT WHEELCHAIR FROM SELF PROPEL TO TRANSIT
armrest. Release sliver bolt once desired height is achieved to securely lock armrest
back in place (see fig 3.1.4).
Wheel mounting
Bracket - Standard
Mount
Figure 3.7.1
Figure 3.1.3
M5 Nut and Bolt
3.2
QUICK RELEASE REAL WHEELS
Wheel mounting
Bracket
3.2.1
To remove rear wheel ensure the brake is off.
Standard
Step 1:
Support the weight of the
wheelchair with one hand by
Figure 3.7.2
holding the push handle.
Step 2:
Push the hub cover and hold
Figure 3.6.2
Figure 3.1.2
Step 1:
Remove the hangers, quick-release wheels
and axles. Place wheelchair on
bench/table or floor as shown in fig 3.7.1.
Figure 3.1.4
Antitipper
Step 2:
Remove the two M6 nuts and bolts
located on the axle block with a 5mm
allen key and 10mm spanner (as supplied
in Karma tool kit). Remove the existing
axle blocks. Mount the new transit block
in front of the antitipper and replace the
two nuts and bolts into the smaller holes.
Figure 3.2
Page 6
Page 10