Billi 926060 Manual do utilizador - Página 7

Procurar online ou descarregar pdf Manual do utilizador para Produto de canalização Billi 926060. Billi 926060 9 páginas. Dispenser options: xl and mixer tap, al
Também para Billi 926060: Manual de instalação (7 páginas)

Imprimir página

Billi Filter Cartridges cont.

Filter Change Reminders

The Billi OmniOne filter change due monitor operates by counting the number of cups dispensed and number of days elapsed until a pre-set

level is reached. The pre-set level is dependent on the type of filter installed.

The following filter change reminders and warnings are displayed in the Filter Status section of the Home Screen.

Due Soon:

Manually settable filter reminder. By default it is set to remind 3 months prior to the pre-set number of days elapsing. It can be set from

the Filter Settings Screens.

Due:

1 month prior to the pre-set number of days elapsing.

Overdue:

The pre-set number of cups or days elapsed has been reached. When this occurs water can no longer be dispensed from the Billi

OmniOne until the filter is replaced.

Filter status indicator lights will also flash as outlined in the Dispenser Icons sections.

Water filters installed in areas with higher levels of turbidity (cloudiness/sediment) will experience a reduced service life. The flow from the

chilled water outlet will decrease as the filters become blocked. It may be necessary to change filters before a filter becomes overdue. The

Due Soon reminder can be set for this purpose to better suit your installation environment.

Standard 5 micron-rated filters generally have a longer service life than premium sub-micron-rated filters.

If particularly dirty water is noticed coming through the water supply (e.g. from other tapware), as sometimes occurs following repairs to

local water mains, immediately turn your Billi OmniOne off at the power source and shut water supply to the system if possible. This will help

prevent premature blocking of the filter cartridges.

Replacement of Filter Cartridges

Periodic replacement of your Billi OmniOne's filter cartridge is necessary to maintain the sparkling cleanliness and purity of your

drinking water.

A replacement filter change service is available. To arrange, contact the Billi Service centre on 1800 812 321 or at www.billi.com.au.

If you wish to install the replacement filter cartridge yourself, filters can be purchased online at www.billi.com.au or through a certified agent

which will provide genuine Billi replacement filter cartridges.

To assist with the replacement of your Billi OmniOne filter cartridge, a series of graphic instruction screens below will guide you through the

required steps. Once the new filter has been installed and the filter flush cycle is complete, check for any water leakage around the system.

Take particular care to ensure the area around the water leakage sensor is dry, located on the lower left hand side of the bulkhead behind

the filter. If you have any questions or concerns during the filter change process, simply contact Billi's experienced technical assistance team

at 1800 812 321 or at www.billi.com.au.

Billi Filter Cartridges cont.

Filter Removal and Replacement Instructions

Important note: Please ensure you remove the foam packing under

the filter before installing.

1. Pull the filter cover edge where it's marked

"OPEN HERE" to open the filter cover (see Diagram 1).

2. Press the

CHANGE FILTER

button in the Filter Screen.

3. Wait a few seconds to allow the filter to de-pressurise.

4. Remove the filter (and filter bypass insert if required)

(see Diagram 2).

a. Hold old the bottom of the filter (or the filter bypass

insert) and pull towards you slowly to hinge the bottom

out. The top of the filter is a hinged cradle assembly and

should stop after approximately 30 degrees of travel.

b. Carefully pull the down in the direction it is tilted until it

pops out.

5. If water spills in the tray at the base of the filter, soak it up

with a cloth or sponge.

6. Fit the new filter by pushing right up into the cradle and

pushing the base of the filter back in until it locks into place.

7. The system will now begin an automatic flush cycle and will

display "FLUSHING FILTERS" in the Main Status Bar.

Dispenser lights will also flash.

8. Check for any leaks from around the filter, hosing or

pipework.

9. Close the filter cover.

10. Once the dispenser lights stop flashing and "SYSTEM

READY" is displayed in the Main Status Bar your system is

ready to use.

Technical support

Warranty registration

Please scan the QR code to re-order f ilters and CO

Diagram 1

Diagram 2