CPflight MCP737PRO3 Manual - Página 2

Procurar online ou descarregar pdf Manual para Painel de controlo CPflight MCP737PRO3. CPflight MCP737PRO3 2 páginas.
Também para CPflight MCP737PRO3: Manual (2 páginas)

Imprimir página

If the A/T switch does not stay in the "On" position check aircraft conditions. The A/T ARM switch

also can be manually disengaged.

ON-FLY BACKLIGHT REGULATION

When the MCP is normal running (starts with Project Magenta, PMDG or in test mode using the

CPflight test software) you can on-fly set backlight brightness. To regulate the backlight brightness

hold pushed any pushbutton and rotates in left or right verse the HDG knob. In this case this

regulation keep maintained for the all the flight duration and will be lost when you will turn off the

MCP. To modify and save these parameters permanently please refer to the next section.

(Backlight Brightness menu).

CONFIGURATION MODE

MCP737PRO3 firmware provides an internal program mode to configure some preferences in the

hardware functionality. With the MCP in stand-by (software not running) push and hold the C/O key

for more than 1 second; this start the hardware in configuration mode. This is the only way to

access to the configuration mode; no PC software program is required to configure the

MCP737PRO3 hardware. In program mode only some keys are operating; the Left Course, IAS and

HDG, ALTITUDE, V/S and Right Course displays show the program title and option to set the

parameters.

C/O key (push and hold for more than 1 second): enter the program menu.

N1 key: scroll to the next program menu.

ENCODERS: set the preferences.

C/O key: save changes and exit the program menu.

Settings are saved in a non-volatile memory when you exit the configuration menu and the MCP

goes in stand-by. Following a description of the menu available in Configuration Mode.

Course

CONFIGURATION MENU

display

IP ADDRESS: allow to set the IP address

parameters. Use the HDG, ALT, V/S and Right

Course knobs to modify (if necessary) the IP

address.

SET PORT: allow to modify (if necessary) the port

SEt

number through ALT knob.

BACKLIGHT BRIGHTNESS: this menu allow to

modify the backlight brightness through HDG knob.

BACKLIGHT CONTROL: This menu allow you to

set the backlight control I, E, ICS through HDG

knob.

I= backlight managed by the simulator

E= backlight managed through an external contact

ICS= backlight managed through MIP737ICS2

module.

HOURS COUNTER (read only): This menu show

Cnt

you the MCP running time in hours.

SERIAL NUMBER (read only): This menu show

SEr

you the product serial number.

FIRMWARE RELEASE (read only): this menu

show you the firmware release.

MAC ADDRESS: allow to set the MAC address

parameters. Use the HEADING knob (if necessary)

MAC

to modify the MAC address.

EXPANSIONS

MCP737PRO3 comes provided with wide expansion capability through the DIN 5 pole auxiliary

socket (Figure1 "C").

This allows you to connect and interface CPflight plug&play expansion. For further information

about modules refer to CPflight website.

AUXILIARY CONNECTIONS

WARNING! The use of auxiliary connector is intended for expertise users. To use these

auxiliary functions it is necessary to connect external pushbuttons and potentiometer. Do

not connect anything coming from any external power source or different by the following

indications; warranty does not cover damages due to incorrect wiring of any external device.

COM: Common pole for External A/T disengage and TO/GA

AT/DIS: External A/T disengage can accept input from a pushbutton. The pushbutton contact must

be open in normal condition and close only when pressed. Releasing the button the contact must

condition and situation (managed by the connected software).

EXTERNAL BACKLIGHT CONTROL: External backlight control accepts input from potentiometer

or switch. Connecting a potentiometer you can regulate the backlight intensity brightness directly

from this input while connecting a switch is possible only to select ON/OFF.

1Kohm to 4,7Kohm 0,5W potentiometer is suitable for a typical setup. To use the external backlight

control set the related preference to "E" in the preferences setting (see "CONFIGURATION MENU"

section).

Important note: when the backlight is controlled through the external control input, it's

status it result independent from any other MCP function.

IAS

Others

display

FIRMWARE UPDATE

The MCP hardware is based on a flash memory microprocessor, on this device has been

HDG

developed one special program (bootloader) that allows to upgrade the firmware. When you install

ALT

Addr

the CPflight driver in the folder will be also installed a program (TCPIP_upgrade.exe) that has to be

V/S

Right Course

used for the upgrade.

Upgrade the microprocessor is a very easy operation and can be done through your ethernet

connection.

Port

ALT

Is necessary to upgrade the firmware time by time, to update new functions that are constantly

developed to improve functionality and compatibility with new products. New firmware release are

HDG

available at CPflight website at MCP737PRO3 page, section technical and documents. Download

briG

(from 0 to 10)

this zip file and extract the included file into a temporary folder. Please pay attention to the

extension of the file: it must be an hex extension.

The revision number is progressive, so a higher number correspond to a latest version. Before to

proceed with the upgrade check the installed firmware revision number. You can see the installed

HDG

version in configuration mode (see related section) or at the MCP startup.

CtrL

(I,E,ICS)

HOW TO UPGRADE

Download the firmware (compressed .zip format) at cpflight website and extract into a temporary

folder. Video tutorial is available at this web page

Hour

xxx

3.php

HDG, ALT

nbr

xxx-xxxx

HDG

Fir

rEL

xxx

Addr

From 0 to 255

display numbers disappear.

Then please run the program TCPIP_upgrade.exe and verify that the TCPIP parameters (TCPIP

address and port) are the same used normally to communicate with your PC. If not please modify it

into the TCP upgrade window program.

return in open condition, do not connect steady position switches

(toggles or similar) to this input. When pushing the button the A/T ARM

switch disengage independently from any other aircraft system

condition.

EXTERNAL TO/GA: External TO/GA can accept input from a

pushbutton. The pushbutton contact must be open in normal condition

and close only when pressed, do not connect steady position switches

to this input. The TO/GA function engaging depends by the aircraft

https://www.cpflight.com/en/mcp737pro3-prod-

Push and hold N1 button until the MCP will start

in demo mode showing the current firmware

version, then release the N1 button.

Push and hold the CMDA button, without release

the CMDA push and hold N1 button until the

At this point click on "Load" menu into

TCPIP_upgrade.exe menu bar and select the file

that you have already downloaded and extracted

into a temporary folder from the site.

At the end of this process, always in the

program menu bar, will activate the option

"Program".

At the end it will appear a window that indicates

the end of the programmation. Close the

upgrade program and disconnect the power

supply from the MCP. Connect another time the

power supply to verify that in the IAS display

window of your MCP will appear the new

release number.

MAIN CHARACTERISTICS

•

Warm white high resolution backlighting frontplate.

•

DIN 5 pole socket for plug&play CPflight modules interface.

•

Green legend backlighted pushbuttons.

•

Displays: Altitude, Vertical Speed, Heading, Speed, Left Course and Right Course.

•

Display characteristics: LED 7 segments. Digit height: 0,3" (7,6mm)

•

Ethernet cable provided and 6Vdc 1A power supply adapter provided

•

Grayhill

Optical encoders with over 1 million cycle rated to set: Altitude, Heading, Speed,

Left and Right Course and Vertical Speed.

•

Knobs: aluminum dust-coated (with symbols on course knobs)

•

BANK ANGLE limit selector (10°, 15°, 20°, 25°, 30°)

•

Electromagnetic disengage Auto Throttle ARM switch with Green LED indication.

•

Toggle switches for Left and Right Flight Director with "MA" Green LED indication.

•

Disengage bar and flight director protections

•

C/O, Speed and Alt Intervention buttons.

•

Ambient light sensor for display brightness regulation.

•

External or internal backlight brightness regulation.

•

Ethernet 16 bit Flash microcontroller.

Is important to be sure to select an hex

estension file. The file will be shown as

MCPPRO2_xxx.hex where xxx will indicate the

firmware release. Now, in the program menu

bar, select the "Connect"

title.

If all is

ok, in this menu will activate the "Erase"

title. At this point select "erase" to delete the old

firmware and prepare the microcontroller for a

new script. The erase operation will take few

seconds.

Please select this title, it will appear a progress

bar that indicates the program progression. This

operation will take about two minutes to

terminate.