Dell DX6000 Manual de instalação e configuração - Página 6

Procurar online ou descarregar pdf Manual de instalação e configuração para Servidor Dell DX6000. Dell DX6000 35 páginas. Rack installation instructions — static rails
Também para Dell DX6000: Manual suplementar (4 páginas), Instruções de instalação do hardware (2 páginas), Manual do utilizador (46 páginas), Manual de instalação e configuração (43 páginas), Manual de iniciação (28 páginas), Aviso (28 páginas), Aviso (20 páginas), Visão geral (19 páginas), Manual de configuração (9 páginas), Manual de configuração (9 páginas), Nota de lançamento (8 páginas), Manual de referência (12 páginas), Manual de configuração (7 páginas), Nota de lançamento (6 páginas), Nota de lançamento (5 páginas), Notas de lançamento (5 páginas), Instruções de instalação (2 páginas), Instruções de instalação (2 páginas)

Imprimir página

Dell DX6000 Manual de instalação e configuração

Chapter 2. Installation and Configuration

2.1. Requirements

2.1.1. Operating System

DX Storage CSN has been developed and tested with 64-bit RHEL 5.5; other RHEL versions or

Linux distributions are not currently supported. Subsequent installation instructions will assume a

pre-installed RHEL Linux environment with either internet connectivity or an alternately configured

RHEL yum repository for use in installing required 3rd party packages.

2.1.2. Network

The CSN requires access to both the external network as well as a dedicated internal network.

The internal private network ensures the DX Storage cluster traffic is protected from unauthorized

access and also that the external network is isolated from both the PXE network boot server

(including DHCP) and cluster multicast traffic. Allocation of the address space in the internal network

is broken down as follows, depending on the network size selected during initial configuration (small

or large):

Network Size

small (/24)

large (/16)

The CSN range provides IPs for the various services on the Primary and Secondary CSNs. The

3rd Party range is provided for 3rd party applications that need to run on the internal network to

interface with the DX Storage cluster. The DHCP range provides an initial IP to DX Storage nodes

during their initial boot until permanent addresses can be assigned to each DX Storage process by

the CSN. Other applications using the CSN's DHCP server on the internal network will reduce the

number of DX Storage that can be booted at the same time. The Netboot range is used to provide

the permanent IPs for all DX Storage processes.

From a network configuration standpoint, the CSN will automatically allocate half of the detected

NICs to the internal network and half of detected NICs to the external network. All NICs allocated

to a network are bonded into a bond interface using Linux mode 6, or balance-alb, bonding. In

configurations where there is both an onboard NIC card as well as an add-on card and the hardware

supports detection of the difference between the two, the internal/external network allocation will

be disbursed across both cards for redundancy. The CSN NIC assignments may not match the

physical NIC ports.

Note

Network switch configuration is outside the scope of the CSN software. Switches must

be properly configured by an experienced system administrator to ensure correct

connectivity and bonding mode support. In particular, administrators must be careful to

not connect the configured internal network ports to the external network.

2.2. Primary vs. Secondary

With two CSNs on an internal network, there must be one CSN designated as the primary. The

primary CSN is responsible for responding to DHCP requests for the internal network and also

CSN

3rd Party

x.y.z.0-16

x.y.z.17-32

x.y.0.0-254

x.y.1.0-254

DHCP

x.y.z.33-48

x.y.2.0-254

DX Storage

Netboot

x.y.z.49-254

x.y.3.0-

x.y.255.254

Version 2.0

December 2010