Dell PowerConnect W-AP105 Manual - Página 29

Procurar online ou descarregar pdf Manual para Interruptor Dell PowerConnect W-AP105. Dell PowerConnect W-AP105 45 páginas. Powerconnect w-ap104 and w-ap105 access points
Também para Dell PowerConnect W-AP105: Manual (10 páginas), Manual de instalação (2 páginas), Especificações (2 páginas), Especificações (2 páginas), Especificações (4 páginas), Manual de instalação (2 páginas)

Imprimir página
Dell PowerConnect W-AP105 Manual
the AP as Remote Mesh Portal by filling in the form appropriately. Detailed steps are listed in
Section "Provisioning an Individual AP" of Chapter "The Basic User-Centric Networks" of the
Aruba OS User Guide. Click "Apply and Reboot" to complete the provisioning process.
a.
During the provisioning process as Remote Mesh Portal, if Pre-shared key is selected to
be the Remote IP Authentication Method, the IKE pre-shared key (which is at least 8
characters in length) is input to the module during provisioning. Generation of this key is
outside the scope of this policy. In the initial provisioning of an AP, this key will be
entered in plaintext; subsequently, during provisioning, it will be entered encrypted over
the secure IPSec session. If certificate based authentication is chosen, AP's RSA key pair
is used to authenticate AP to controller during IPSec. AP's RSA private key is contained
in the AP's non volatile memory and is generated at manufacturing time in factory.
b.
During the provisioning process as Remote Mesh Portal, the WPA2 PSK is input to the
module via the corresponding Mesh cluster profile. This key is stored on flash encrypted.
9.
Via the logging facility of the staging controller, ensure that the module (the AP) is successfully
provisioned with firmware and configuration
10. Terminate the administrative session
11. Disconnect the module from the staging controller, and install it on the deployment network; when
power is applied, the module will attempt to discover and connect to an Aruba Mobility Controller
on the network.
To verify that the module is in FIPS mode, do the following:
1.
Log into the administrative console of the Aruba Mobility Controller
2.
Verify that the module is connected to the Mobility Controller
Verify that the module has FIPS mode enabled by issuing command "show ap ap-name <ap-
3.
name> config"
4.
Terminate the administrative session

3.3.4 Configuring Remote Mesh Point FIPS Mode

1.
Apply TELs according to the directions in section 3.2
2.
Log into the administrative console of the staging controller
3.
Deploying the AP in Remote Mesh Point mode, create the corresponding Mesh Profiles on the
controller as described in detail in Section "Mesh Points" of Chapter "Secure Enterprise Mesh" of
the Aruba OS User Manual.
a.
For mesh configurations, configure a WPA2 PSK which is 16 ASCII characters or 64
hexadecimal digits in length; generation of such keys is outside the scope of this policy.
4.
Enable FIPS mode on the controller. This is accomplished by going to the
> Controller > System Settings page (this is the default page when you click the Configuration tab), and
clicking the FIPS Mode for Mobility Controller Enable checkbox
5.
Enable FIPS mode on the AP. This accomplished by going to the
Configuration > AP Group page. There, you click the Edit button for the appropriate AP group, and then
select AP > AP System Profile.
configuration.
6.
If the staging controller does not provide PoE, either ensure the presence of a PoE injector for the
LAN connection between the module and the controller, or ensure the presence of a DC power
supply appropriate to the particular model of the module.
7.
Connect the module via an Ethernet cable to the staging controller; note that this should be a direct
connection, with no intervening network or devices; if PoE is being supplied by an injector, this
Then, check the "Fips Enable" box, check "Apply", and save the
29
Configuration > Network
.
Configuration > Wireless > AP