Dell PowerConnect W-AP105 Manual de instalação - Página 2

Procurar online ou descarregar pdf Manual de instalação para Interruptor Dell PowerConnect W-AP105. Dell PowerConnect W-AP105 2 páginas. Powerconnect w-ap104 and w-ap105 access points
Também para Dell PowerConnect W-AP105: Manual (10 páginas), Manual (45 páginas), Manual de instalação (2 páginas), Especificações (2 páginas), Especificações (2 páginas), Especificações (4 páginas)

Imprimir página

Dell PowerConnect W-AP105 Manual de instalação

Connecting Required Cables

Install cables in accordance with all applicable local and national regulations and

practices.

Ethernet Ports

The RJ45 Ethernet port (ENET) supports 10/100/1000Base-T auto-sensing MDI/

MDX connections. Use these ports to connect the AP to a twisted pair Ethernet LAN

segment or directly to an Dell Controller. Use a 4- or 8-conductor, Category 5 UTP

cable up to 100 m (325 feet) long.

The 10/100/1000 Mbps Ethernet port is on the back of the AP. The port has an RJ-45

female connector with the pin-outs shown in

Figure

Figure 6

Gigabit Ethernet Port Pin-Out

Signal Name

RJ-45 Female

Function

Pin-Out

BI_DA+

Bi-directional pair +A

BI_DA-

Bi-directional pair -A

BI_DB+

Bi-directional pair +B

BI_DC+

Bi-directional pair +C

BI_DC-

Bi-directional pair -C

BI_DB-

Bi-directional pair -B

BI_DD+

Bi-directional pair +D

BI_DD-

Bi-directional pair -D

Serial Console Port

The serial console port (Console) allows you to connect the AP to a serial terminal or

a laptop for direct local management. This port is an RJ-45 female connector with the

pinouts described in

Figure

7. Connect this port in one of the following ways:

Connect it directly to a terminal or terminal server using an Ethernet cable.

Use a modular adapter to convert the RJ-45 (female) connector on the AP to a

DB-9 (male) connector, and connect the adapter to a laptop using an RS-232

cable. See

Figure 8

for connector details of the adapter.

Figure 7

Serial Port Pin-Out

Serial

RJ-45 Female

Console Port

Pin-Out

TxD

GND

RxD

Direction

Input

Output

Figure 8

RJ-45 (Female) to DB-9 (Male) Modular Adapter Conversion

RJ-45 Female

Internal

DB-9 Male

Pin-Out

Connections

Pin-Out

RJ-45

DB-9

TxD

GND

RxD

Direction

Input

Output

Power Connection

The W-AP105 has a single 12V DC power jack socket to support powering through an

AC-to-DC power adapter.

Note: If both POE and DC power are available, the AP uses POE even when there is

not enough POE voltage available to power the AP.

Verifying Post-Installation Connectivity

The integrated LEDs on the AP can be used to verify that the AP is receiving power

and initializing successfully (see

Table

1). Refer to the ArubaOS Quick Start Guide

for further details on verifying post-installation network connectivity.

LED

Color/State

Meaning

PWR

Off

No power to AP

Green flashing

System initializing

Red steady

System failed to initialize,

contact TAC

Green steady

Power on, device ready

ENET

Off

No link

(10/100/1000 Mbps)

Green on

1000 Mbps link

Amber on

10/100 Mbps link

Green flashing

Ethernet link activity

LED

Color/State

11A/N

Off

Amber

Green

Green flashing

11B/G/N

Off

Amber

Green

Green flashing

Configuring the W-AP105

AP Provisioning/Reprovisioning

Provisioning parameters are unique to each AP. These local AP parameters are

initially configured on the controller which are then pushed out to the AP and stored

on the AP itself. Dell recommends that provisioning settings be configured via the

ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details.

AP Configuration

Configuration parameters are network or controller specific and are configured and

stored on the controller. Network configuration settings are pushed out to the AP(s)

but remain stored on the controller.

Configuration settings can be configured via the ArubaOS Web UI, ArubaOS CLI, or

Dell MMS. Refer to their respective guides for further details: the ArubaOS User

Guide or Dell Mobility Management System User Guide.

Product Specifications

Mechanical

Dimensions (antenna stowed) (HxWxD):

5.2 inches x 5.3 inches x 1.8 inches

13.2 cm x 13.5 cm x 4.5 cm

Ground

Weight: 300g/0.66 lbs.

RxD

Temperature:

TxD

Operating: 0ºC to 50ºC (32ºF to 122ºF)

Storage: –10ºC to 70ºC (14ºF to 158ºF)

Relative Humidity: 5% to 95% non-condensing

Altitude: 8,000 ft @ 28ºC (82.4ºF)

Mounting: Wall, ceiling, or desktop mountable

Antennas: Integrated

Visual Status Indicators (LEDs): See

Table 1

Electrical

Ethernet:

1 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces

MDI/MDX

IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-

Power over Ethernet (IEEE 802.3af compliant), 48V DC/350mA (see

for pin configuration)

Power:

12 VDC power interface, supports powering through an AC-to-DC power

adapter

Note: If a power adapter other than the one provided by Dell Networks is used in

the US or Canada, it should be cULus (NRTL) Listed, with an output rated 12 VDC,

minimum 1.25A, marked "LPS" or "Class 2," and suitable for plugging into a

standard power receptacle in the US and Canada.

Wireless LAN

Network Standards: IEEE 802.11b, IEEE 802.11g, IEEE 802.11a, and

IEEE 802.11n (draft)

Antenna Type:

Internal

2x 802.11a/n

2x 802.11b/g/n

Antenna Gain (Integrated Antennas):

2.4 – 2.5 GHz/2.5 dBi (max)

Meaning

5.180 – 5.825 GHz/4.0 dBi (max)

5 GHz radio is disabled

Radio Technology:

5 GHz radio enabled in

Orthogonal Frequency Division Multiplexing (OFDM)

WLAN mode

Direct Sequence Spread Spectrum (DSSS)

5 GHz radio enabled in 11n

Radio Modulation Type:

mode

802.11b - CCK, BPSK, QPSK

5 GHz Air Monitor or RF

Protect mode

802.11g - CCK, BPSK, QPSK,16-QAM, 64-QAM

802.11a - BPSK, QPSK,16-QAM, 64-QAM

2.4 GHz radio disabled

802.11n draft 2.0

2.4 GHz radio enabled in

WLAN mode

Media Access Control: CSMA/CA with ACK

2.4 GHz radio enabled in 11n

Supported Frequency Bands 2.4GHz:

mode

2.400 ~ 2.4835GHz (Global), channels country specific

2.4 GHz Air Monitor or RF

Supported Frequency Bands 5GHz:

Protect mode

5.150 ~ 5.250GHz (low band), country-specific

5.250 ~ 5.350GHz (mid band), country-specific

5.470 ~ 5.725GHz (Europe), country-specific

5.725 ~ 5.825GHz GHz (high band), country-specific

Data Rates:

802.11b - 1, 2, 5.5, 11 Mbps per channel

802.11g - 6, 9, 12, 18, 24, 36, 48 and 54 Mbps per channel

802.11a - 6, 9, 12, 18, 24, 36, 48 and 54 Mbps per channel

802.11n - Data rate MCS0 – MCS15 (from 6.5 Mbps to 300 Mbps)

Proper Disposal of Dell Equipment

For the most current information on Global Environmental Compliance and Dell

products please refer to the Dell PowerConnect W-Series Safety, Environmental, and

Regulatory Information document or see our website at www.dell.com.

European Union RoHS

Dell products also comply with the EU Restriction of

Hazardous Substances Directive 2002/95/EC (RoHS). EU

RoHS restricts the use of specific hazardous materials in the

manufacture of electrical and electronic equipment. Specifically, restricted materials

under the RoHS Directive are Lead (including Solder used in printed circuit

assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Dell

products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in

solder used in printed circuit assemblies). Products and packaging will be marked

with the "RoHS" label shown at the left indicating conformance to this Directive.

Safety and Regulatory Compliance

Dell provides a multi-language document containing country specific restrictions and

additional safety and regulatory information for all Dell hardware products. The Dell

PowerConnect W-Series Safety, Environmental, and Regulatory Information document

is included with this product

Caution: RF Radiation Exposure Statement: This equipment complies with FCC RF

radiation exposure limits. This equipment should be installed and operated with a

minimum distance of 13.78 inches (35 cm) between the radiator and your body for

2.4 GHz and 5 GHz operations. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter. When operated in

the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to

reduce the potential for harmful interference with co-channel Mobile Satellite

Systems.

Figure 6

Dell PowerConnect W-AP105

Access Point

Installation Guide

Contacting Support

Web Site Support

Main Site

www.dell.com

Support Site

https://support.dell.com

Dell Documentation

https://support.dell.com/manuals

System®, and other registered marks are trademarks of Aruba Networks, Inc. Dell™,

the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc.

Originated in the USA. Any other trademarks appearing in this manual are the property of

their respective companies.

Open Source Code

Certain Aruba products include Open Source software code developed by third parties,

including software code subject to the GNU General Public License (GPL), GNU Lesser

General Public License (LGPL), or other Open Source Licenses. The Open Source code

used can be found at this site:

http://www.arubanetworks.com/open_source

Legal Notice

The use of Aruba Networks, Inc. switching platforms and software, by all individuals or

corporations, to terminate other vendors' VPN client devices constitutes complete

acceptance of liability by that individual or corporation for this action and indemnifies, in

full, Aruba Networks, Inc. from any and all legal actions that might be taken against it

with respect to infringement of copyright on behalf of those vendors.

www.Dell.com

Dell PowerConnect W-AP105 Access Point | Installation Guide

Part Number 0510747-02 | July 2010