32 Degrees Icon-E Manual do Proprietário - Página 3

Procurar online ou descarregar pdf Manual do Proprietário para Equipamento de paintball 32 Degrees Icon-E. 32 Degrees Icon-E 6 páginas.

Imprimir página
Oil) into the Tank Adapter (#14). This will run the oil through the valve to ensure the O-
Rings stay moist and do not dry or crack. Failure to do so may cause the marker to leak.
5. Place the leading end of the propellant cylinder threads into the threaded interface of the
Tank Adapter (14).
6. Without pushing, twist the propellant cylinder in a clockwise direction and allow the cylinder
threads to "draw" it into the Tank Adapter. DO NOT force the cylinder; it could cause cross
threading, not covered by warranty.
7. Screw the propellant cylinder completely in until it is firmly seated.
Attaching Feeder/Hopper
1. Confirm that the Barrel Plug is properly installed on the marker and is on "Safe."
2. Attach the vertical feed elbow that is provided with your marker and hand tighten the
thumb adjustment screws onto the Vertical Feed Neck (#11). DO NOT OVER TIGHTEN.
Over tightening can cause the vertical feed elbow to crack.
3. Press the neck of the Feeder/Hopper into the Vertical Feed Neck (11) until it is
completely seated.
4. Position the Feeder/Hopper so that the lid is facing the rear of the marker and the
Feeder/Hopper is parallel to the Main Body (34).
5. Tighten down the top screw on the vertical feed neck to secure the feeder/hopper
into place, again being sure not to over tighten.
Loading Paintballs
The performance of your marker is directly affected by the quality of paintballs used. We
highly recommend Diablo paintballs to give you satisfaction and success on the playing field.
1. Confirm that the Barrel Plug is properly installed and the marker in on "Safe."
2. Point the marker in a safe direction and load paintballs in the Feeder/Hopper. If you
are using a non-motorized hopper, be sure to leave some room in the hopper for the
balls to feed properly.
4
13
45
18
11
23
34
26
33
8
7
16
16 16
16
16
9
6
22
10
16
31
15A
29
30
32
14
15A
15
25
19
19
ICON E Parts List
11. Vertical Feed Neck
20. Grip Panel Screws
1. Hammer
12. Velocity Adjuster
21. Grip Frame Screws
2. Main Spring
3. Recoil Pad
B. Locking Set Screw
22. Vertical ASA Screw
4. Spring Strut
13. Metal Ball Detent
23. Barrel
5. Quick Strip Pin
14. Tank Adapter
24. Hammer Plug
A. R-Clip
15. Air Filter
25. Gas Line
A. Air Filter O-Ring
26. Low Pressure
6. Gas Valve
16. Multi-Use O-Ring
Chamber
7. Cupseal
17. Grip Frame Pin Set
27. Sight Rail
8. Valve Spring
9. Valve Gas Plug
18. Vertical Feed Screws
A. Sight Rail Screw
10. Valve Stop Pin
19. Bottomline Screws
28. Bolt
ELECTRONIC GRIP

FRAME Parts List

E01.
Wiring Harness/Trigger
E04.
ON/OFF Switch Screws
E06.
Switch
E05.
Solenoid Set Screws
E07.
E02.
Solenoid
E03.
Circuit Board
5A
16 16
28C
27A
28
27
28A
3
2
4
1
16
12B
12
5
24
E04
17
E05
37
38
35
20
E02
36
21
21
E19
40
E01
E03
E06
46
E07
20
A. Connecting Pin
36. Grip Panels
C. Connecting Pin Set
37. Electronic Sear
Screw
38. Sear Spring
29. Drop Forward
40. Trigger
30. Drop Forward
45. Barrel Plug
Screws
46. Drop Forward
31. Expansion Chamber
Re-tension Screw
32. Gas-Thru
33. Vertical ASA
34. Main Body
35. Grip Frame
Circuit Board Screw
Battery Lead
5
5