EarthQuake 8900E Manual do operador - Página 4
Procurar online ou descarregar pdf Manual do operador para Equipamento para relva e jardim EarthQuake 8900E. EarthQuake 8900E 12 páginas. Power earth auger
Também para EarthQuake 8900E: Manual do operador (12 páginas)
ARDISAM
OPERA
OPERA
OPERA TION
TION
TION
TION
OPERA
OPERA
TION
REGISTRATION FORM
REGISTRATION FORM
REGISTRATION FORM
REGISTRATION FORM
REGISTRATION FORM
Complete and return. Your auger's serial number is
located on the powerhead decal under the Barracuda name.
Record this number and the model number in the space
provided on page 2 of this manual. You will need these
numbers if you order parts. Fill out and mail the
registration card located in your parts packet. Warranty is
valid only if your completed registration card is
received by Ardisam, Inc., at time of purchase.
SP SP SP SP SPARK PL
ARK PL
ARK PL
UG INST
UG INST
ARK PL
ARK PLUG INST
UG INST
UG INSTALLA
If your powerhead does not have the spark plug already
installed for you. You will have to install it following the
instructions given below.
1. Locate the spark plug in the parts packet.
2. With powerhead laying on its side, place spark plug in
hole on right side of engine.
3. Turn by hand until snug.
4. Use a 3/4" wrench or socket to tighten up.
OPERATION
OPERATION
OPERATION
OPERATION
OPERATION
CAUTION
Please do not start your auger until you have read the
Engine Manual that came with your engine, and the section
in this manual titled Safety. If you have read these, follow
the steps below to start your auger. Always perform this
pre-start checklist before starting the engine.
1. Read engine operating manual and follow instructions
for fuel type, starting, etc. BE SURE TO USE
PROPER GAS/OIL MIXTURE.
2. The clutch will transfer maximum power after about
two hours of normal operation. During this break-in
period clutch slippage may occur. The clutch should be
kept free of oil or other moisture for efficient operation.
3. Dig holes without placing excessive body weight on the
unit. The auger operates most efficiently with a shaving
action caused by the weight of the unit itself.
4. Never run engine indoors. Exhaust fumes are deadly.
5. Do not use an ice auger in earth.
6. The ice auger blade protector should be attached to the
auger head when not in use. This will protect the cutting
edge of the ice auger blade.
ALLA
ALLA
TION
TION
ALLATION
ALLA
TION
TION
FUEL MIXTURE
FUEL MIXTURE
FUEL MIXTURE
FUEL MIXTURE
FUEL MIXTURE
Never fill fuel tank indoors. Never add gas when engine is
running or hot from operation. Do not smoke when filling
fuel tank.
This engine uses a gas/oil mixture. DO NOT RUN ENGINE
ON STRAIGHT GAS ONLY. ENGINE DAMAGE WILL
RESULT!
1. Mix clean, fresh, lead-free gasoline (minimum of 77
octane) with a high quality 2 cycle engine oil at the ratio
of 5 oz. oil to 1 gallon gasoline. (Refer to your engine
manual for further information on fuel.)
2. Mix fuel in a 1 or 2 gallon container approved for
gasoline.
3. Loosen fuel cap slowly. Rest the cap on a clean surface.
4. Carefully pour fuel into the tank. Avoid spillage.
5. Immediately replace fuel cap and hand tighten. Wipe up
any fuel spillage.
ST ST ST ST STARTING AND ST
ARTING AND ST
ARTING AND ST
ARTING AND ST
ARTING AND STOPPING
Do not hold throttle lever wide open while starting. Loss of
control of auger could result.
1. Open gas cap vent if your engine is so equipped (silver
steel cap).
2. Flip the toggle switch to the on position.
3. Move red choke lever to full choke position if engine is
cold.
4. Pull recoil starter until engine fires.
5. Move choke lever to half choke position (midway
between off and full).
6. Pull recoil starter until engine runs.
7. Run engine 30 to 45 seconds at full throttle on half
choke position until engine warms up.
8. Move choke lever to off position.
TO STOP: Flip the toggle switch to the off position.
Page 4
CAUTION
OPPING
OPPING
OPPING
OPPING
CAUTION