Allmatic ACTION Instruções de instalação - Página 2

Procurar online ou descarregar pdf Instruções de instalação para Unidade de controlo Allmatic ACTION. Allmatic ACTION 5 páginas. For tecno-cat

Imprimir página

4. Settings

This chapter contains important informations for a secure and correct installation. Follow exactly all the instructions because a wrong installation can

cause serious damages to the automation.

4.1 Preliminary checks.

Before powering up the control panel, check the wirings. In particular check that there are no damaged wires, short-circuits between wires and that

all the accessories are connected to the terminal board in the points indicated in the diagram on the previous page.

Once the power supply is on check that:

The POWER LED is constantly on.

The radio module is inserted and working.

The motor and the encoder connections are correct by following the procedure described below:

This procedure allows us to check the rotation sense of the motors, any possible blockages during the movement of the chain. It is important to

carry out this check in order to locate any wiring errors or anything else that can jeopardize.

N.B.: During this handling the photocells, the radio and the buttons are NOT active.

SW1 position

AUT

MAN

SW1 position

MAN

AUT

4.2 Manual moving

This procedure must be carried out ONLY by the installer and ONLY during the setting up of the system. The movement can be effectuated in partic-

ular situations in which it is not possible to move the chain to the closed (UP) position in automatic mode.

SW1 position

AUT

MAN

WARNING: the reactivation of the automatic mode (AUT) implies the use of the reached position as totally closed position.

WARNING: During the manually moving, the anti-squeezing safety is not active.

4.3 Memorisation of the transmitters (only with the chain totally closed (UP) ).

Memorize at least one single channel transmitter. The control unit is provided with the rolling code decodifying. To vary the decodifying see

paragraph 5.3. During the normal functioning the first memorized button executes the step-by-step function (opening and closing), the second button

(optional) controls the courtesy light.

SW1 position

MAN

AUT

6-1622349 rev.3 28/03/2019

Push the BLUE button. The chain

has to move downwards

Yes

Release the BLUE button and press the YELLOW

button. The chain must move upwards. Return it to

the completely closed ( UP ) position.

To raise the chain

To lower the chain

Press and release the RED button.

The flashing LED will remain con-

stantly lit.

Yes

Press the 1st button on the remote

control. The flashing signal emits 2

slow flashes followed by a fast flash

Yes

The 1st button is memorized. Press

and release the RED button. The flash-

ing LED will remain constantly lit.

Yes

Press the 2nd button on the remote

control. The flashing signal emits one

slow flash followed by 1 fast flash.

Yes

The 2 buttons are memorized and the

procedure ends.

ITA

The Chain does not move

The chain moves upwards

Check the cables and

repeat the test.

Press the yellow button.

Press the blue button

Check that the chain is completely closed

(UP) and that the SW1 is in position

AUTO, repeat again from the beginning.

If the flashing signal has emitted 1 slow flash followed by 1 fast flash, the button

pressed was already memorized and you can continue with the procedure. Contrari-

ly check that the remote control is working, that it has the same decoding set in the

control unit and that the radio module is inserted. At this stage repeat the test.

Check that the chain is completely up and that

SW1 is in the AUTO position and repeat the test.

Check that the remote control is working, that it has the same decod-

ing set in the control panel and that the radio module is inserted. At

this stage repeat the test.

ENG

FRA

ESP

DEU

POR

Check the cables and

repeat the test.

Modify the orientation of the 2 jumpers

present on the card. If not present, invert

the phases of the motor. Repeat the test.

pag. 2 di 5