Alloy LED AL-60-03-0008 Especificações e instruções - Página 6

Procurar online ou descarregar pdf Especificações e instruções para Interruptor Alloy LED AL-60-03-0008. Alloy LED AL-60-03-0008 7 páginas. Led wifi controller hub

Imprimir página

Alloy LED AL-60-03-0008 Especificações e instruções

First way:

1)Selected any one room and there will be small mark on the

upper right side.

2)Press

room button

3)Press learning key

on RF controllers SR-1009xx series

4)Touch the color wheel,LED lighting will blink to confirm room

designation

Controls & Features

Delete

Press at

learning key

on receiver(SR-1009Fxx) over 5

seconds until

LED

light flash, then delete the learned ID.

Room Button

Second way:

1. Press the Room button

2. Short press the middle of a room picture.

3. A green checkmark at the upper right corner of the picture indicates it has

been selected. Multiple rooms can be choose at the same time.

4. Press the Room button again to confirm the room selection. The top of the

picture will indicate the name of the selected room.

Long press the middle of the room picture to turn on/off the corresponding

rooms/zones. There will be a red "off" mark at the upper right corner of the

room picture when the room is switched off.

Color Wheel

There are four different color wheels you can select for a room that has not been

edited: RGB-W/RGB, CDW, CCT, and single color.

Scroll through color wheels by swiping the upper area of the screen down. (P17)

Or fast press twice to enter the color wheel selection interface to choose a color

P18

P19

wheel (P18)

room button

on RF controllers SR-1009xx series

18)

Run/Pause Button

c. pause&run button(P19)

Running button exist in RGB, CDW color wheel interface, they

are similar so here will take RGB as an example to explain.

learning key

on receiver(SR-1009Fxx) over 5

The Run/Pause button (P19) can be used in the RGB and CDW color wheels: the fol-

Attention

LED

light flash, then delete the learned ID.

lowing shows RGB as an example.

Press the Run/Pause button to run a mode. Press once to run the first mode. Press

the button again to pause. Press again to run the next mode. There are a total of 10

build-in modes. If you select a color on the wheel after pausing, the mode will return

to the first mode.

Long press the Run/Pause button and the LED lights will flash twice to indicate that

e. RGB/CDW brightness level line(P21)

the running mode in different zones will be switched from Synchronized to col-

This button exist in RGB/CDW interface, they are similar, so

here will take RGB as an example to explain.

or-changing or from color-changing to Synchronized running.

1)Short press the button

2)Brightness level can be adjusted

from 0-255 to an accurate color.

Music (P20)

Attention

Before adjust the color by color line, LED might in already in

an existing color, so we need zero clearing each channel first:

In Voice mode, the LED lighting will change in response to a voice nearby. The louder

moving each channel in any level between 1-225, then move it

the voice, the faster the speed of this mode. The LED lighting will return to the adjusted

back to zero, then RGB lighting will off which means zero

clearing successfully.

speed when no voice is present.

f. W button(P22)

This button only exists in RGB channels color wheel interface to

In Music mode, the LED lighting will change in response to a voice nearby. The louder

adjust W channel brightness independently.

the voice, the faster the speed of this mode. The LED lighting will return to the adjust-

Long press W button

to ON/OFF W channel independently.

In RGB color wheel interface,it only adjusts R,G and B three channels

ed speed when no voice is present. When you press the music note key, your mobile

brightness,and cannot adjusts W channel.We need use W button

to adjust W channel brightness independently.

device's music player will open.

g. Brightness button(P23)

Brightness button exist in RGB, CDW and CCT color wheel

Move the slider to the left to increase the microphone sensitivity, so that a quieter voice

interface.

P18

P19

will slow down the mode. Lower the mic sensitivity by moving the slider to the right.

In CDW and CCT color wheel interface, it adjusts all channels

brightness.

18)

www.AlloyLED.com

Page 6 of 7

Running & Pause button

Fastest speed

Moving speed

adjust libe

Lowest speed

Running & Pause button

Fastest speed

Moving speed

adjust libe

Lowest speed

Call: 800.910.LEDS [5337]

choose successfully, multiple rooms can be choose at same time

Press room button again be confirm the rooms' selection

Upper area will indicate room's name we selected.

b. color wheel

There will be four different color wheels we can select if we did

not edit the room: RGB, CDW, CCT, Single color.

1)Slide the upper areas from top to down to choose color wheel

from one to one. (P16,P17)

Learning ( combining)

First way:

1)Selected any one room and there will be small mark on the

upper right side.

2)Press

room button

P15

3)Press learning key

on RF controllers SR-1009xx series

d. music(P20)

4)Touch the color wheel,LED lighting will blink to confirm room

designation

Delete

Press at

learning key

on receiver(SR-1009Fxx) over 5

seconds until

LED

light flash, then delete the learned ID.

Manual

Second way:

a. Room button(P27,P28)

RGB-W

Choose Room button

/RGB

Short press middle of zone picture

The highest,a low voice

Mark on the upper right side of room picture to indicate

will affect the moving

choose successfully, multiple rooms can be choose at same time

speed lowest

CDW

Press room button again be confirm the rooms' selection

Upper area will indicate room's name we selected.

b. color wheel

There will be four different color wheels we can select if we did

not edit the room: RGB, CDW, CCT, Single color.

1)Slide the upper areas from top to down to choose color wheel

from one to one. (P16,P17)

P21

P18

P15

18)

d. music(P20)

c. pause&run button(P19)

Running button exist in RGB, CDW color wheel interface, they

are similar so here will take RGB as an example to explain.

Attention

P23

h. Save button(P24)

1.Save

The highest,a low voice

1)Select rooms/zones

will affect the moving

2)Select color or moving modes

speed lowest

3)Short press save button

4)Long press any button of S1-S8

5)LED lighting will flash indicate save successfully.

2.Recall

1)Select rooms/zones

e. RGB/CDW brightness level line(P21)

2)Short press save button

This button exist in RGB/CDW interface, they are similar, so

3)short press saved button in S1-S8

here will take RGB as an example to explain.

4)LED will indicate saved color or moving modes

| Text: 510.400.6690

1)Short press the button

2)Brightness level can be adjusted

from 0-255 to an accurate color.

First way:

1)Selected any one room and there will be small mark

upper right side.

2)Press

room button

3)Press learning key

on RF controllers SR-1009xx

4)Touch the color wheel,LED lighting will blink to confi

designation

Delete

Press at

learning key

on receiver(SR-1009Fxx) ove

seconds until

LED

light flash, then delete the learned I

Second way:

P16

P17

CCT

When choose

open your local music

palyer

single

The lowest,need a high

color

voice affect moving speed.

P20

P18

P19

100% brightness

18)

c. pause&run button(P19)

Running button exist in RGB, CDW color wheel interfa

W channel's

Run/Pause button

are similar so here will take RGB as an example to ex

Running & Pause button

brightness level

Attention

1% brightness

Fastest speed

Adjust speed

Moving speed

adjust libe

P22

Slowest speed

Lowest speed

P19

100% brightness

e. RGB/CDW brightness level line(P21)

P16

P17

This button exist in RGB/CDW interface, they are sim

here will take RGB as an example to explain.

1)Short press the button

2)Brightness level can be adjusted

1% brightness

from 0-255 to an accurate color.

Attention

Before adjust the color by color line, LED might in a

an existing color, so we need zero clearing each ch

moving each channel in any level between 1-225, th

P24

back to zero, then RGB lighting will off which mean

When choose

clearing successfully.

open your local music

palyer

f. W button(P22)

This button only exists in RGB channels color wheel

The lowest,need a high

adjust W channel brightness independently.

voice affect moving speed.

Long press W button

to ON/OFF W channel inde

In RGB color wheel interface,it only adjusts R,G and

brightness,and cannot adjusts W channel.We need u

to adjust W channel brightness independently.

P20

g. Brightness button(P23)

Brightness button exist in RGB, CDW and CCT color

[email protected]

interface.

In CDW and CCT color wheel interface, it adjusts all c

100% brightness

brightness.

P29

Runn

Fas

,it will

Mov

adju

Low

P29

,it will

v2.3