Dialogic DM3 Media Boards DMV600BTEP Cartão de instalação rápida

Procurar online ou descarregar pdf Cartão de instalação rápida para Placa de rede Dialogic DM3 Media Boards DMV600BTEP. Dialogic DM3 Media Boards DMV600BTEP 2 páginas. Dm3 media boards quick install card for pci

Imprimir página

Dialogic

DM3 Media Boards

Quick Install Card for PCI

DMV600BTEP

Part number: 64-0066-02

Dialogic Corporation.

Before You Begin

Protecting the Board from Damage

CAUTION

All computer boards are sensitive to

electrostatic discharge ("ESD"). Handle all static-

sensitive boards and components at a static-safe work

area, and observe anti-static precautions at all times.

If you are not familiar with ESD safety precautions, visit

http://www.dialogic.com/support/hwinstall

Unpacking the Board

Unpack the Dialogic

DM3 Media Board ("board") according

to the following steps:

Prepare a static-safeguarded work area.

Carefully remove the board from the shipping

carton and anti-static packaging. Handle the board

by the edges and avoid touching the board's

components.

Lay the board on the static-dissipative work

surface.

Note: Place boards in static-shielding bags when carrying

boards from station to station.

CAUTION: Do not remove the board from the anti-static

packaging until you are ready to install it. Observe proper

anti-static precautions at all times.

Configuring the Hardware

Board Identification

The DM3 device driver, part of the system software, assigns

board instance numbers in ascending order (beginning with 0)

as it detects each board in your system. A board instance

number is the identification (ID) number used by the system

software to recognize the board.

NOTE: If you add or remove a board, the system may

change the existing board instance (ID) numbers.

Loopback

to learn more.

After the hardware and the system software are installed,

refer to the Dialogic

configuration utility to retrieve the board instance (ID)

number(s) assigned to the board(s) in your system.

See the DCM online help for details about board

identification.

In a Linux system, you must set SW1 to a unique number for

each DM3 board in your system. Use a non-magnetic

screwdriver to turn SW1 to 1 of 16 board settings, 0-9 or A-F.

After the hardware and system software are installed, refer to

the proper configuration files to retrieve the board instance

(ID) number(s) assigned to the board(s) in your system.

For more information about Linux configuration files, see the

Dialogic Configuration Guide supplied with your system

release.

CH4 CH3 CH2 CH1

Red

Yellow

Green

Windows System

Configuration Manager (DCM)

Linux System

Physical Description

RJ-48C jacks: Connectors (2) to external digital

telephone network interface.

General Network Interface Alarm LED

Power LED

Reset LED

SW1: Rotary switch to set board identification

(Linux systems only).

POST LEDs: Indicate Power On Self Test

(POST) status during power up.

Alarm LEDs (CH1 and CH2 only): Indicate

network alarms for each trunk.

Red: Alarm to indicate loss of signal.

Yellow: Alarm to indicate loss of frame

synchronization at far end of external

network.

Green: Indicates signal present; powered up

and receiving signal from external sources.

Loopback: Indicates loopback mode is

activated.

CT/MVIP Bus Termination Jumpers: Bus

signal is terminated when the corresponding

jumper clip is installed. Signal must be

terminated only on boards at each end of the

JP2A

CT Bus cable.

JP2B

JP2A: CT Bus termination jumper

JP2B: MVIP Bus termination jumper

P3: CT Bus connector

ISA Edge Retainer

10. Signal Processing Daughterboard

Installing the Hardware

NOTE: Dialogic recommends that you install the hardware

before the system software. However, if you are adding a

DM3 board to an existing DM3 system, you do not need to

uninstall existing DM3 software.

1. With your computer on the static-safe work area, switch

off the power and disconnect all power cords from the

electrical outlets.

2. Remove the chassis cover plate.

3. Select an empty PCI expansion bus slot and remove the

slot's retaining screw and access cover plate (if

applicable).

4. If you are not installing your board in an ISA form

factor PCI slot, remove the ISA edge retainer from the

board.

5. Using the slot's board guides, insert the edge connector

of the board into the bus slot. Press firmly until the

board is securely seated in the slot.