Dialogic DN/I300TEPHMP Manual de instalação

Procurar online ou descarregar pdf Manual de instalação para Hardware de rede Dialogic DN/I300TEPHMP. Dialogic DN/I300TEPHMP 2 páginas. Digital network interface board

Imprimir página

Dialogic

DN/I300TEPHMP Digital

Network Interface Board

Installation Guide

1. Product Description

The Dialogic

DN/I300TEPHMP Digital Network

Interface Board ("board") is a high-density, high-

performance, network interface board in a universal

PCI form factor with one T1/E1 digital network

interface. This board is designed to be used with

Dialogic

Host Media Processing (HMP) software

(Release 2.0 or higher). The DN/I300TEPHMP

Digital Network Interface Board includes the

following components:

RJ-48C Jack: One connector to a T1 or E1 trunk.

General Network Interface Alarm LED: When lit,

indicates an alarm condition is present on the

trunk.

Reset LED: When lit, indicates that the board is in

the reset state.

Power LED: When lit, indicates power is on.

SW1: Rotary switch used to set board identification

(Linux system only).

Alarm/Status LEDs: A set of four LEDs for the

trunk. During power-up, the LEDs indicate Power

On Self Test (POST) status. After the board is

started, the green, yellow, and red LEDs indicate

normal operation or Carrier Failure Alarms (CFAs)

as shown in the following table. The Loopback

LED indicates when the trunk is in loopback

mode.

Green

Yellow Red

Conditions

OFF

Normal Operation

OFF

Loss of Signal (LOS)

OFF

Red Alarm

OFF

Yellow Alarm/Remote Alarm

Indicator (RAI)

Alarm Indicator Signal (AIS)

Part number: 64-0083-02

Physical Layout

CT Bus

Connector

Optional ISA Edge

Retainer

(on reverse

side of board)

Universal PCI

Bus Connector

CT Bus Connector: Connector to CT Bus.

Optional ISA Edge Retainer: Bracket used to

install board in an ISA form factor PCI slot.

P5: CT Bus Termination Jumper Block. Factory

default is unterminated. Signals must be

terminated only on boards at each end of an

optional CT Bus cable.

JP3X11 and JP4X11: Power-off Default Front End

Loopback for the trunk. Factory default is enabled

(jumper clips installed).

JP5: Boot up Default Front End Loopback. Factory

default is enabled (jumper clip removed).

Universal PCI Bus Connector: Connector to

universal PCI Bus slot.

Additional Information

Additional information about the DN/I300TEPHMP

Digital Network Interface Board is available from a

number of sources.

Red

Yellow

Green

Loopback

Power LED

Reset LED

General Network

Alarm LED

RJ-48C Jack

The product data sheet, available at

http://

, provides a

www.dialogic.com/products/list.asp

functional description as well as information about

applications and configurations, features, and

technical specifications.

Refer to the Release Guide and the online Release

Update for your Dialogic

Host Media Processing

(HMP) software release to verify that the DN/

I300TEPHMP Digital Network Interface Board is

supported in the release and for information on any

new features or issues that may relate to it.

The Regulatory Notices document that is packed

with each Dialogic

DN/I300TEPHMP Digital

Network Interface Board contains safety warnings

and national requirements for proper operation of

telecommunications equipment.

2. Before You Begin

Protecting the Board from Damage

CAUTION: All computer boards are sensitive to

electrostatic discharge ("ESD"). Handle all static-

sensitive boards and components at a static-safe

work area, and observe anti-static precautions at all

times.

If you are not familiar with ESD safety precautions,

visit http://dialogic.com/support/hwinstall to learn

more.

Unpacking the Board

CAUTION: Do not remove the board from the anti-

static packaging until you are ready to install it.

Observe proper anti-static precautions at all times.

Unpack the board according to the following steps:

1. Prepare a static-safeguarded work area.

2. Carefully remove the board from the shipping

carton and static-shielding bag. Handle the

board by the edges and avoid touching the

board's components.

3. Lay the board on the static-safe work surface.

Note: Place boards in static-shielding bags when

carrying boards from station to station.

Setting the Board ID

The device driver assigns board instance numbers

in ascending order (beginning with 0) as it detects

each board in your system. A board instance

number is the identification (ID) number used by the

Dialogic

Host Media Processing (HMP) software to

recognize the board.

Note: If you add or remove a board, the system

may change the existing board instance numbers,

depending on the PCI bus and slot number where

the board is installed or removed.

In a Windows system, leave SW1 (see Physical

Layout) set to the factory default of 0 to let the

system automatically assign board instance

numbers by PCI bus slot number. After the hardware

and the Dialogic HMP software are installed, refer to

the Dialogic

Configuration Manager (DCM) to

retrieve the assigned board instance ID number(s).

Dialogic

Configuration Manager (DCM) is a utility

that enables you to add new boards to your system,

start and stop system service, and work with board

configuration data. This utility can be accessed from

the Start menu in the Dialogic HMP software

program folder. For more information about board

identification, see the DCM online help.

In a Linux system, you must set SW1 to a unique

number for each installed board. Use a non-

magnetic screwdriver to turn SW1 to one of 16

board settings, 0–9 or A–F. After the hardware and

the Dialogic HMP software are installed, refer to the

proper configuration files to retrieve the assigned

board instance ID number(s). For more information

about Linux configuration files, see the Dialogic

HMP software release documentation.

Setting CT Bus Termination

This section applies if you are using a CT Bus cable

to connect your board to other boards in the system.

Bus signals are terminated when the CT Bus jumper

clip is installed. To terminate bus signals, install a

jumper clip on the pair of CT Bus termination pins

only on boards located at each end of the bus cable.

Factory default is unterminated (jumper clip

removed).

The following figure shows the pair of pins used for

CT Bus termination. Refer to P5 in the Physical

Layout figure for the location of the jumper block.

CT Bus

Termination

Connector

Setting Power-off Default Front End

Loopback

When the system shuts down (powers off), the

board enables analog loopback to the connected

trunk line. Factory default setting is enabled for the

trunk (jumper clips are installed). To disable, remove

the pair of jumper clips for the trunk.

The pair of jumpers for the trunk is JP3X11 and

JP4X11. Refer to the Physical Layout figure for the

location of the jumpers.