Miller ADI 253 Manual de instruções - Página 7
Procurar online ou descarregar pdf Manual de instruções para Sistema de soldadura Miller ADI 253. Miller ADI 253 36 páginas.
Imprimir página-
FIRE
OR
EXPLOSION
hazard.
Do not install
or
place
unit on, over,
or
near
A
combustible surfaces.
Do
not
install unit
near
flammables.
Do not overload
building winng
be
sure
power
supply system
is
properly
sized, rated,
and
protected
to handle this unit.
FALLING UNIT
can cause
injury
Use
lifting
eye
to
lift unit
only,
NOT
running
gear, gas
cylinders,
or
any other accessories.
Use
equipment
of
adequate capacity
to
lift and
support
unit.
If
using
lift
forks
to
move
unit,
be
sure
forks
are
long enough
to extend
beyond opposite
side of
unit.
OVERUSE
can cause
OVERHEATING
Allow
cooling period;
follow rated
duty cycle.
Reduce current
or
reduce
duty cycle
before
starting
to
weld
again.
Do
not
block
or
filter airflow to unit.
STATIC
(ESD~
can
damage
PC boards.
Put
on
grounded
wrist
strap
BEFORE
handling
boards
or
parts.
Use proper
static-proof bags
and boxes
to
store,
move,
or
ship
PC boards.
MOVING PARTS
can cause
injury.
Keep
away from
moving
parts.
Keep
away from
pinch points
such
as
drive
rolls.
WELDING WIRE
Can
cause
injury.
Do
not
press gun
trigger
until instructed
to
do
so.
Do not
point
gun toward any
part
of the
body,
other
people,
or
any metal when
threading
welding
wire.
:1.4
Principal Safety
Standards
Safety
in
Welding
and
Cutting,
ANSI Standard
Z49.1 from American
Welding Society,
550 N.W. LeJeune
Rd,
Miami FL 33126
Safety
and Health
Standards,
OSHA 29 CFR
1910,
from
Superinten
dent of
Documents,
U.S. Government
Printing
Office,
Washington,
D.C. 20402.
Recommended Safe Practices for the
Preparation
for
Welding
and
Cutting
of Containers That Have Held Hazardous
Substances,
American
Welding Society
Standard AWS F4.1
from American
Welding
Society,
550 N.W. LeJeune
Rd, Miami,
FL 33126
National
Electrical
Code,
NFPA Standard
70,
from National Fire
Protection
Association,
Batteryrnarci,
Park,
Quincy,
MA 02269.
MOVING PARTS
can cause
injury.
Keep
away
from
moving
parts
such
as
fans.
Keep
all
doors, panels,
covers, and
guards
closed and
securely
in
place.
H.F. RADIATION
can cause
interference.
High-frequency (H.F.)
can
interfere with radio
navigation, safety
services, computers,
and
communications
equipment.
Have
only qualified
persons familiar with
electronic
equipment perform
this installation.
The
user
is
responsible
for
having
a
qualified
electrician
promptly
correct
any interference
problem resulting
from the
installation.
If
notified
by
the FCC about
interference, stop
using
the
equipment
at
once.
Have the installation
regularly
checked and maintained.
Keep high-frequency
source
doors and
panels tightly
shut,
keep spark
gaps
at correct
setting,
and
use
grounding
and
shielding
to minimize
the
possibility
of interference.
ARC WELDING
can cause
interference.
Electromagnetic
energy
can
interfere with
sensitive
electronic
equipment
such
as
computers
and
computer-driven equipment
such
as
robots.
Be
sure
all
equipment
in the
welding
area
is
electromagnetically compatible.
To reduce
possible
interference, keep
weld cables
as
short
as
possible,
close
together,
and down
low,
such
as
on
the floor.
Locate
welding operation
100 meters from
any
sensitive elec
tronic
equipment.
Be
sure
this
welding
machine is installed and
grounded
according
to
this manual.
If interference still
occurs,
the
user
must take extra
measures
such
as
moving
the
welding
machine,
using
shielded
cables,
using
line
filters,
or
shielding
the work
area.
Safe
Handling
of
Compressed
Gases in
Cylinders,
CGA
Pamphlet
P-i,
from
Compressed
Gas
Association,
1235 Jefferson Davis
Highway,
Suite
501,
Arlington,
VA 22202.
Code for
Safety
in
Welding
and
Cutting,
CSA Standard Wi
17.2,
from
Canadian Standards
Association,
Standards
Sales,
178 Rexdale
Boulevard, Rexdale, Ontario,
Canada
M9W 1 R3.
Safe Practices For
Occupation
And Educational
Eye
And Face
Protection,
ANSI Standard Z87.1
,
from American National Standards
Institute,
1430
Broadway,
New
York,
NY 10018.
Cutting
And
Welding
Processes,
NFPA Standard 51
B,
from National
Fire Protection
Association,
Batterymarch
Park,
Quincy,
MA 02269.
1 3
Additional
Symbols
for
Installation,
Operation,
and Maintenance
OM-221
7
3