ABB DODGE PARA-FLEX Manual

Procurar online ou descarregar pdf Manual para Equipamento industrial ABB DODGE PARA-FLEX. ABB DODGE PARA-FLEX 4 páginas. Couplings includes atex approved couplings

Imprimir página

DODGE

PARA-FLEX

These instructions must be read thoroughly before installation or operation. This instruction manual was accurate at the time of printing. Please see

baldor.com for updated instruction manuals.

Note! The manufacturer of these products, Baldor Electric Company, became ABB Motors and Mechanical Inc. on March 1, 2018.

Nameplates, Declaration of Conformity and other collateral material may contain the company name of Baldor Electric Company and the brand

names of Baldor-Dodge and Baldor-Reliance until such time as all materials have been updated to reflect our new corporate identity.

WARNING: To ensure the drive is not unexpectedly started, turn

off and lock-out or tag power source before proceeding. Failure to

observe these precautions could result in bodily injury.

WARNING: All products over 25 kg (55 lbs) are noted on the

shipping package. Proper lifting practices are required for these

products.

WARNING: Because of the possible danger to person(s) or

property from accidents which may result from the improper use

of products, it is important that correct procedures be followed.

Products must be used in accordance with the engineering

information specified in the catalog. Proper installation,

maintenance and operation procedures must be observed.

The instructions in the instruction manuals must be followed.

Inspections should be made as necessary to assure safe

operation under prevailing conditions. Proper guards and other

suitable safety devices or procedures as may be desirable or as

may be specified in safety codes should be provided, and are

neither provided by ABB nor are the responsibility of ABB. This

unit and its associated equipment must be installed, adjusted

and maintained by qualified personnel who are familiar with the

construction and operation of all equipment in the system and the

potential hazards involved. When risk to persons or property may

be involved, a holding device must be an integral part of the driven

equipment beyond the speed reducer output shaft.

FLANGE INSTALLATION

For the TAPER-LOCK

the flange per instructions included with bushing or find the

instruction manuals at www.baldor.com.

Check the axial float of the shafts. Position the shafts at the

mid-point of the float. Where Limited End Float is required

or Sleeve Bearings are used, consult Mechanical Power

Transmission Support for application assistance.

Referring to Figure 1 and Table 1, observe the "B"

dimension for the coupling size being installed. Mount and

position the flanges on the shafts so that dimension "B" is

achieved when the shafts are in their final position.

For the TAPER-LOCK and QD flanges, secure the flange

assembly to the shaft by positioning the assembly onto the

shaft allowing for small axial movement which will occur

during tightening procedure. Alternately torque hardware to

recommended torque setting. For the clearance fit straight

bore (FBX) flange, tighten the set screws to values listed in

Table 2. Align flanges using precision equipment such as

dial indicators or laser equipment.

If precision equipment is not available, scales, straight

edges, and calipers can be used as less accurate means of

alignment. If using a scale or calipers, refer to Figure 3 and

check the angular misalignment by measuring dimension

"B" at four places 90° apart. Adjust the equipment until

the four measurements do not vary more than value "C" in

Table 1. If using a straight edge, check the parallel offset

by laying the straight edge across the outside diameter of

the flanges in four places 90° apart. The gap between the

flange and straight edge should not exceed 1/32" (0.79mm).

To achieve maximum coupling performance, align the

coupling as accurately as possible during initial installation.

Remove any anti-rust lubricants or oil from the grooved

side of the clamp rings. Loosen but do not remove clamp

ring screws until only one or two threads are engaged and

proceed to the section on flexible element installation.

Couplings:

and QD flanges, install bushing in

Includes ATEX Approved Couplings

Two-Piece Flange Styles

Flexible

Element

Internal

Flange

Clamp Ring

PX40 STANDARD TAPER-LOCK

PX50-120QD FLANGE ASSEMBLY

Figure 1 - Two-Piece Flange Styles

Three-Piece Flange Styles

Disassemble the clamp rings from the flanges. Place the

external clamp rings on the shafts with the grooved side

facing the shaft end.

For the TAPER-LOCK flange, install the bushing in the

flange per instructions included with bushing.

Check the axial float of the shafts. Position the shafts at the

mid-point of the float. Where Limited End Float is required

or Sleeve Bearings are used, consult Mechanical Power

Transmission Support for application assistance.

Referring to Figure 2 and Table 1, observe the "B"

dimension for the coupling size being installed. Mount and

position the flanges on the shafts so that dimension "B" is

achieved when the shafts are in their final position.

For the TAPER-LOCK flange, secure the flange assembly

to the shaft by positioning the assembly onto the shaft

allowing for small axial movement which will occur during

tightening procedure. Alternately torque setscrews to

recommended torque setting. For the clearance fit straight

bore (FBX) flange, tighten the set screws to values listed in

Table 2. Align flanges using precision equipment such as

dial indicators or laser equipment.

If precision equipment is not available, scales, straight

edges, and calipers can be used as less accurate means of

alignment. If using a scale or calipers, refer to Figure 3 and

check the angular misalignment by measuring dimension

"B" at four places 90° apart. Adjust the equipment until

the four measurements do not vary more than value "C" in

Table 1. If using a straight edge, check the parallel offset

by laying the straight edge across the outside diameter of

the flanges in four places 90° apart. The gap between the

flange and straight edge should not exceed 1/32" (0.79mm).

To achieve maximum coupling performance, align the

coupling as accurately as possible during initial installation.

Remove any anti-rust lubricants or oil from the element side

of the clamp rings. Assemble clamp rings on the flanges

engaging only one or two threads and proceed to the

section on flexible element installation.

Flexible

External

Element

Clamp Ring

Flange

Flexible

Element

Flange

Internal

Clamp Ring

PX140 thru 320 TAPER-LOCK

PX140-200QD FLANGE ASSEMBLY