Diamond +7ECEH4R00 Manual - Página 5

Procurar online ou descarregar pdf Manual para Equipamento comercial para alimentos Diamond +7ECEH4R00. Diamond +7ECEH4R00 13 páginas.
Também para Diamond +7ECEH4R00: Manual de instruções (13 páginas), Manual (13 páginas)

Imprimir página

IV. THE ENVIRONMENT

1. PACKING

Packing materials are environment friendly and can

be stored without risk, or burned in a special waste

incineration plant.

Recyclable plastic components are marked with:

Polyethylene: outer wrapping, instruction booklet

bag, gas nozzle bag.

Polypropylene: roof packing panels, straps.

Polystyrene foam: corner protectors.

2. USE

Our appliances offer high performance and efficiency. To re-

duce consumption of electricity, water or gas, do not use the

appliance empty or in conditions that compromise optimal

efficiency (e.g. with doors or lids open, etc.); the appliance is

used in a well-ventilated place to avoid the creation of

dangerous mixtures of unburnt gases in the room. Whenever

possible, pre-heat only before use.

3. CLEANING

In order to reduce the emission of pollutants into the

environment, clean the appliance (externally and when

necessary internally) with products that are more than 90%

biodegradable (for further information, see chap. V

"CLEANING").

4. DISPOSAL

Do not disperse in the environment. Our

appliances are manufactured using more

than 90% (in weight) recyclable metals

(stainless steel, iron, aluminium, galvanised

sheet, copper, etc.).

Make the appliance unusable by removing

the power cable and any compartment or cavity closing

mechanisms (when present) in order to avoid the risk of

someone becoming closed inside.

V. INSTALLATION

•

Carefully read the installation and maintenance

procedures given in this instruction manual before

installing the appliance.

• Installation, maintenance and conversion to

another type of gas must only be carried out by

qualified personnel authorised by the

manufacturer.

•

Failure to observe the correct appliance installation,

conversion and modification procedures can cause

damage to the appliance, danger to persons and

invalidates the Manufacturer's warranty.

1. REFERENCE STANDARDS

• Install the appliance in accordance with the safety

regulations and local laws of the country where used.

• AUSTRALIA: this appliance shall be installed only by

authorised persons and in accordance with the

manufacturer's installation instructions, local gas fitting

regulations,municipal building codes, electrical wiring

regulations, local water supply regulations, AS5601-gas

installation, health authorites and any other statutory

regulations.

2. UNPACKING

IMPORTANT!

Immediately check for any damage caused during

transport.

• The forwarder is responsible for the goods during transport

and delivery.

• Inspect the packing before and after unloading.

• Make a complaint to the forwarder in case of visible or

hidden damage, reporting any damage or shortages on

the dispatch note on delivery.

• The driver must sign the dispatch note: The forwarder can

reject the claim if the dispatch note is not signed (the

forwarder can provide the necessary form).

• Unpack, taking care not to damage the

equipment. Wear protective gloves.

• Carefully remove the protective film from metal surfaces

and clean any traces of glue with a suitable solvent.

• For hidden damage or shortages becoming apparent only

after unpacking, request the forwarder for inspection of

the goods within and not later than 15 days of delivery.

• Keep all the documentation contained in the packing.

3. POSITIONING

• Handle the equipment with care in order to avoid damage

or danger to persons. Use a pallet for handling and

positioning.

• The installation diagram given in this instruction manual

gives the appliance dimensions and the position of

connections (gas, electricity, water). Check that they are

available and ready for making all the necessary

connections.

• The appliance can be installed separately or combined

with other appliances of the same range.

• The appliances are not designed for built-in installation.

Leave at least 10 cm between the appliance and side or

rear non-combustible walls.

Leave at least 25 cm between the appliance and side or

rear walls made from combustible materials.

• Suitably insulate surfaces that are at distances less than

those recommended.

• Maintain an adequate distance between the appliance and

any combustible walls. Do not store or use flammable

materials and liquids near the appliance.

• Leave an adequate space between the appliance and any

side walls in order to enable subsequent servicing or

maintenance operations.

• Check and if necessary level the appliance after

positioning. Incorrect levelling of the appliance can affect

combustion and cause malfunctioning.