AQUAPHOR S800 Manual de operação - Página 13

Procurar online ou descarregar pdf Manual de operação para Dispensador de água AQUAPHOR S800. AQUAPHOR S800 20 páginas.

Imprimir página

Mode of enhanced

washing from iron

Step 1. Turning on / off the enhanced iron

cleaning mode

Press and hold

to turn the feature on or off. In the mode

of enhanced cleaning from iron, a more intensive washing

of the softener with saline occurs, which contributes to

more efficient cleaning of the sorbent from iron. When this

mode is enabled, regeneration occurs every other day. To

achieve the desired effect, the mode of enhanced iron

washing should be switched on for at least 2 weeks. De-

pending on the iron content of the water, it is recommend-

ed to carry out this procedure at least once a year.

Advanced settings

Advanced settings allow you to select the brine regener-

ation mode, turn on the 96h mode, change the liter/gallon

and mg/L/gpg units, and set the regeneration start time.

Please be careful when using advanced settings.

Salt regeneration mode change

A. Press and hold

controller will beep and display the brine regenera-

tion mode on the display.

B. Press

to cycle through AU, HC, and HE modes.

Press

to save the selected option and proceed

to step 2.

Salt regeneration modes:

AU (Auto mode) – in this mode, the controller monitors

the daily water consumption and regulates the

amount of salt for regeneration. If the 96h mode is

disabled, the controller will regenerate 2 times a

week if there is water demand.

HC (High capacity mode) – fixed setting of salt regen-

eration, which allows less frequent washing of the

sorbent.

HE (High economy mode) – fixed salt regeneration set-

ting, which reduces the amount of water to be treat-

ed between flushes, but significantly saves salt.

Enabling / Disabling the forced regeneration mode "72-

96 hours"

In this mode, the controller will regenerate automatically,

at the appointed time once every 3–4 days, if normal

regeneration did not occur during this interval.

Press

to turn 96h mode on or off. The display on the

right side will show or turn off the indicator 96h. Click

to save your settings and move on to the next step.

96h mode. Activation of the 96h mode ensures that the

regeneration process is carried out at least 2 times

a week. This mode must be switched on if there is iron

and/or manganese in the source water.

and

for about 4 seconds, the

NOTE: More frequent regenerations help the softener to

recover more effectively from iron.

Unit switching: gallon / liter

Press C to switch gallon/liter units. The changes will be

displayed on the screen as gallons or liters. Click

save your settings and move on to the next step.

Setting the regeneration start time

A. Press

to set/change regeneration start time

(hours). Press

to save the settings and go to the

minutes setting.

B. Press

to change the minutes at which regener-

ation starts. Click

the home screen.

NOTE: Time is shown in 24 hour format.

Recommendations for

effective use softener

To get the most out of your softener, follow these

guidelines:

• Add salt if the level is below the water level in the

brine tank. The salt level must always be at least 1/3

of the full load.

• It is recommended to use pure salt in tablets or gran-

ules. Don't use rock salt.

• Once every 6 months it is recommended to use an ion

exchanger cleaner.

ATTENTION! Do not mix different types of salt.

• In the event of a power outage, check the correctness

of the controller settings (type of regeneration, water

parameters, time); if necessary, set the correct values.

(See the Controller Setup section).

• Program the softener to regenerate at times of the

day when you don't normally use water. If you have

several water treatment devices that require regener-

ation, the time between device regenerations should

be at least two hours.

• Please note that other water-using devices, such as

washing machines and dishwashers, should not be

running while the softener is regenerating.

• Protect the softener from freezing, including the drain

line.

• Follow the requirements for operation, maintenance

and placement of the softener.

• If the softener runs out of salt during operation: add

salt; wait at least two hours for the salt to dissolve and

then start the regeneration. To do this, press and hold

the R button for 5 seconds; regeneration will be com-

pleted in approximately 30–40 minutes, after which

the softener will return to normal operation.

to save the settings and go to