Diamond OX-MS Manual do utilizador - Página 5

Procurar online ou descarregar pdf Manual do utilizador para Equipamento comercial para alimentos Diamond OX-MS. Diamond OX-MS 7 páginas. Self levelling dispensers for crockery

Imprimir página

MANUAL MOBILE UNITS

dispenser. Use the cover - also during issue - as much as possible against loss of

energy. Place the cover on the dispenser if it's not in use; the dispenser and the plates

will stay clean and dustfree.

A cover is not standard on the dispenser, but can be obtained, - when ordered -

as an accessory. A cover can be ordered seperatly; inform at your supplier.

THE HEATING-ELEMENT AUTOMATICALLY SWITCHES OFF AT A TEMPERATURE

OF MAX ± 120 °C AT THE TOP OF THE UNIT

AT THE BOTTOM, JUST ABOVE THE ELEMENT THE TEMPERATURE WILL BE

ABOUT ± 10 TO 20 °C HIGHER

AFTER A FEW HOURS OF HEATING THE TOPSIDE OF THE CABINET GETS VERY

WARM; USE A PUSH-BAR OR SPECIAL GLOVES WHEN MOVING THE UNIT

7. Cleaning of the dispenser.

1) Remove dust/dirt from the cover and the cabinet of the dispenser daily with a moist

cloth.

2) Remove dust/dirt in the dispenser a least twice a year:

a) Switch to "0".

b) Take the plug form the power-supply.

c) Remove the crockery and the platform from the dispenser.

d) Dust or vacuumclean the inside.

e) Clean the inside with a moist cloth.

DO NOT USE A WET, BUT A MOIST CLOTH OR SPONGE WHILE CLEANING

THE DISPENSER WITH HEATING

DO NOT USE A HIGH-PRESSURE SQUIRT WHILE CLEANING THE DISPENSER

WITH HEATING

DO NOT USE AGGRESSIVE DETERGENTS WHILE CLEANING THE PC COVERS

(IN A DISHWASHING-MACHINE)

3) Put the plug into the power-supply, the platform and the crockery back into the

dispenser.

8. Maintenance of the dispenser.

In appendix B all the parts are listed.

1) Check the right spring-strength at least twice a year.

As the result of permanent stretching and under influence of constant heating the

spring-strength is reduced.

Hang in all available, but not yet used, springs in or replace (all) springs by new ones:

a) Switch to "0".

b) Take the plug from the power-supply.

c) Remove the crockery and the platform from the dispenser.

d) Hang not yet used springs onto the spring-ring of the platform or repace the old

springs by new ones.

MANUAL MOBILE UNITS

DO NOT PUSH THE PLATFORM DOWNWARD WHILE ADJUSTING THE SPRING- STRENGTH; THERE

SHOULD BE NO TENSION ON THE SPRINGS

DIVIDE THE SPRING-STRENGTH EQUALLY ON THE SPRING-RING; NOT ALL

SPRINGS ON ONE SIDE AND ON THE OTHER SIDE NO SPRINGS

2) Check all fastening bolts and nuts of the castors twice a year.

Check if all castors roll and swivel well, if not:

a) take the wheel out of the fork.

b) clean the wheel and pivot-joint with a moist cloth with cleaner.

REPLACE WORN WHEELS IN TIME AND LOST NUTS DIRECTLY

DO FIX THE BOLTS OF THE CASTORPLATE IN A CROSS AND NOT TOO TIGHT

(FIXED IS OK)

USE A SAFETY-NUT OR A NUT IN COMBINATION WITH A RING

3) Check the the condition of the electrical parts 1 or 2 times a year.

a) Switch to "0".

b) Take the plug form the power-supply.

c) Remove the heating-drawer and the operating-panel.

All electrical parts are now visible and can be reached.

MAINTENANCE AND REPARATION SHOULD ONLY BE DONE BY - IN THE FIELD

OF ELECTRICITY - QUALIFIED PERSONNEL

ONLY USE ORIGINAL PARTS OR PARTS WITH EXACT THE SAME SPECIFICATIONS,

OR PARTS WITH A CERTIFICATION

CHECK THE FAN SEVERAL TIMES A YEAR, THE FAN SUCKS IN EXTRA DIRT

AND DUST, THIS CAUSES REDUCED FUNCTIONING OR DAMAGE TO THE FAN

4) Replace parts in bad condition or defective parts:

a) Read the apendixes A en B of this manual or inform at your supplier or servicedesk.

b) Place all new parts in the same way as the old parts.

c) Place the heating-drawer and the operating-panel back into the dispenser.

5) Put the plug into the power-supply, the platform and the crockery into the dispenser.