Aquasafe Aquarium II Dual R.O./D.I. System Manual de instruções de instalação - Página 5

Procurar online ou descarregar pdf Manual de instruções de instalação para Sistemas de filtragem de água Aquasafe Aquarium II Dual R.O./D.I. System. Aquasafe Aquarium II Dual R.O./D.I. System 15 páginas.

Imprimir página

You can now turn your home's emergency cold water shut off valve back to its "ON" position. Please

note: By turning the cold water shut off valve back to its "ON" position you are allowing for the flow of

cold water to the system. The system's three pre-filters will then fill with water which will come out of

the blue tube that is placed in your kitchen sink.

Allow the water to run through your system for 20 minutes to ensure proper flushing of the three pre-

filters. After the 20 minute pre-filter flush, turn the manual shut off valve, found on the feed water line

(see Fig 9), 90 degrees to the tubing as this will stop the flow of water to your system.

Next, following the diagram below, remove the blue tubing inserted into the "OUTPUT" (Right Side) of

the prefilters that you just used to flush the three prefilters.

Figure 10

How to

disconnect tubing

using the 'quick-

release' collet

to de-pressurize your system before removing tubing from any fitting on your system. To de-pressurize

your system you simply need to turn the manual shut off valve, found on the feed water line, to its 90

degree (OFF) position, then turn your tank top valve, found on top of the water holding tank (not yet

installed at this point), to the 90 degree (OFF) position and then press down on your faucet. De-pres-

surizing your system is extremely easy and takes just seconds.

6.0 R.O. Membrane feed water line hook-up (pre-filter to R.O. Membrane)

Take the short white tube connected to the "IN" side of the 4 way auto shut-off valve (ASV) on the top

of the unit and insert it into the elbow adaptor on the "OUTPUT" (right side) of the pre-filters. (Fig. 11)

Remember to insert the tubing firmly. Next, take the short white line connected to the "OUT" side of

the 4 way auto shut-off valve (ASV) on the top of the unit and insert it into the elbow adaptor on the

cap of the R.O. Membrane housing (Fig 11). These two white tubes complete the connection between

the pre-filters and the R.O. Membrane.

Figure 11

yellow tubing

Connect the short

(comes pre-connected

to ow restrictor)

white water lines

attached to the

auto shut-off

valve

Connect

short white

tube to elbow

on OUTPUT side

of pre- lters

page 6 | Maximus II Installation Instructions 05/13 | www.aquasafecanada.com

To remove tubing from any point on

your system simply follow this dia-

gram (Fig. 10) You can easily remove

the tubing from any fitting on your

system by removing the blue "C" clip

which will expose the "collet". Then

simply push in the collet so that it is

flush with the fitting and then pull

out the tubing.

Please note: In the future, be sure

blue tubing (comes pre-connected)

4 way auto

Connect short white

shut-o valve

tube to elbow on

(ASV)

R.O. Membrane

housing cap

Manual

Shut-O Valve

in OFF position

NOTE: Back View - hanging

bracket not shown for clarity

7.0 Setting the Flow Restriction Ratios of your System.

Using the same blue tubing used to flush the pre-filters, insert one end of the blue tubing into the E–Z

Flush Flow Restrictor (Fig 12). After you have inserted the blue tubing into the E–Z Flush Flow Restric-

tor, insert the other end of the blue tubing into your kitchen sink. The water that will flow through

your E-Z Flush Flow Restrictor is referred to as "BRINE" water and will discharge into your drain washing

away the harmful particulates removed by the R.O Membrane.

Next, get a bowl or a bucket and place it under the short piece of blue tubing that is coming out of the

auto shut-off valve (ASV). The water that will flow out of the short piece of blue tubing that is com-

ing out of the auto shut-off valve (ASV) is the purified water produced by the R.O. Membrane and is

referred to as "PERMEATE" water.

4 way auto

Figure 12

shut-o valve

Preparing to set

(ASV)

up the E-Z Flush

Flow Restrictor

NOTE: Back View - hanging

bracket not shown for clarity

Now, turn the dial on top of the E–Z Flush Flow Restrictor clockwise (Right), entirely closing the valve

of the E–Z Flush Flow Restrictor and then turn the Manual Shut-Off Valve (Fig.12) found on the feed

water supply line of your system to its "ON" Position. Within a moment PERMEATE water will begin to

flow out of the short blue piece of tubing coming out of the Auto Shut Off Valve (ASV), at the rate of a

very fast drip to a slow trickle. Air inside the R.O. Membrane will be forced out causing the fast drip or

slow trickle to sputter with the air escaping. Wait 2-3 minutes for the air to fully purge so that a steady

output is achieved from the R.O. Membrane.

Next, carefully open the dial on-top of the E-Z flush Flow restrictor counter clockwise (left) VERY SLOW-

LY until the amount of BRINE water flowing through the E-Z Flush Flow Restrictor is flowing THREE

TIMES FASTER than that of the PERMEATE water flow coming out of the RO Membrane. In this way

you achieve a 3:1 ratio where 3 parts is BRINE water and 1 part is PERMEATE water. (You can do this by

judging the flow visually or see the note below for how to do a timed measurement.)

When you are confident that you have properly set the flow ratios as explained above, locate the

"marker sleeve" which is found directly under the top dial of E–Z Flush Flow Restrictor. Screw this

marker sleeve down the threads of the shaft of the dial so that it is flush with the main body of the E–Z

Flush Flow Restrictor. This will serve as an exacting marker to the amount of flow restriction you have

set. Now turn the Manual Shut-Off Valve back to its (OFF) position and remove the blue tubing from

the E–Z Flush Flow Restrictor.

www.aquasafecanada.com | Maximus II Installation Instructions 05/13 | page 7

Put a bowl or bucket under the short piece of blue

tubing coming out of the ASV to catch the 'PERMEATE'

water (cleaned by the R.O. Membrane)

Connect long blue tubing

to E-Z Flush Flow Restrictor

and put other end in sink.

to water supply

Manual

Shut-O Valve

E-Z Flush Flow

Restrictor

'BRINE' water rejected

by R.O. membrane

Close the E-Z Flush Flow Restrictor and

turn the Manual Shut-O Valve on