Panasonic WV-SW396 Manual de instalação - Página 13

Procurar online ou descarregar pdf Manual de instalação para Câmara de vídeo Panasonic WV-SW396. Panasonic WV-SW396 40 páginas. Ip video cameras
Também para Panasonic WV-SW396: Especificação (2 páginas), Manual de instalação (40 páginas), Especificações (2 páginas), Nota de integração (8 páginas)

Imprimir página

Precautions for installation

Panasonic assumes no responsibility for injuries or

property damage resulting from failures arising out

of improper installation or operation inconsistent

with this documentation.

Power supply

This product has no power switch. Use a power supply

device equipped with the ON-OFF switch for servicing.

When the power cable of the product is connected to the

power supply device, the power will be supplied to the

product. When the product is supplied, the product will

perform panning, tilting, zooming and focusing.

Before cleaning the product, make sure that the power

cable is not connected to the main power supply.

Installation area for this product

Select an appropriate place for the installation area (such

as a strong wall or ceiling) in your particular environment.

Mounting method for this product

• This product is designed to be used as a pendant

mount camera. If the product is mounted on a desk-

top or at a slant, it may not work correctly or its life-

time may be shorten.

• Mount the product horizontally so that the dome sec-

tion faces downward.

Ceiling pendant type mount bracket/Wall mount

bracket

• When pendant-mounting on a ceiling on a bracket

that is locally procured, use the attachment pipe.

• When installing on a wall, use Wall Mount Bracket

WV-Q122A (option). When this product and camera

mount bracket are mounted on a ceiling or a wall, use

the screws described in the following table. The

screws that secure the product are not supplied.

Prepare them according to the material and strength

of the area where the product is to be installed.

Camera

Weight

Approx. 4.6 kg {10.15 lbs}

Appropriate mount bracket

Model No.

WV-Q122A

Weight

Approx. 2 kg {4.42 lbs}

Mount type

On wall

Part to be mounted on a ceiling/wall

Recommended screw M8

Number of screw

Pull-out capacity of a

823 N {185 lbf}

single screw

• Ensure that the mounting surface, anchor and screws

are sufficiently strong.

• Do not mount the product on a plaster board or a

wooden section because they are too weak. If the

product is unavoidably mounted on such a section,

the section shall be sufficiently reinforced.

Do not place this product in the following places:

• Locations where a chemical agent is used such as a

swimming pool

• Locations subject to humidity, dust, steam and oil

smoke

• Locations where a radiation, an X-ray, a strong radio

wave or a strong magnetic field is generated

• Locations where corrosive gas is produced, locations

where it may be damaged by briny air such as sea-

shores

• Locations where the temperature is not within the

specified range (☞ page 35).

• Locations subject to vibrations (This product is not

designed for on-vehicle use.)

• Locations subject to condensation as the result of

severe changes in temperature (In case of installing

the product in such locations, the dome cover may

become foggy or condensation may be caused on

the cover.)

Screw tightening

• The screws and bolts must be tightened with an

appropriate tightening torque according to the materi-

al and strength of the installation area.

• Do not use an impact driver. Use of an impact driver

may damage the screws or cause tightening exces-

sively.

• When a screw is tightened, make the screw at a right

angle to the surface. After tightening the screws or

bolts, perform visual check to ensure tightening is

enough and there is no backlash.

Remove the Protection Cover from the dome cover

after the installation is complete.

Remove the cover film from the dome section of the

dome cover after the installation is complete.

SW396

SW395

Be sure to remove this product if it is not in use.

Shielded (STP) LAN cables must be used with this

unit to ensure compliance with EMC standards. *

* For Europe

SW396A

SW395A