Diamond Audio HEX480.4 Manual do Proprietário - Página 7
Procurar online ou descarregar pdf Manual do Proprietário para Amplificador Diamond Audio HEX480.4. Diamond Audio HEX480.4 16 páginas. Multi-channels
INSTALLATION
1
and when there is a protection fault. The "OPS" LED is illuminated when there is a problem with your amplifier. Please contact your authorized
Diamond Audio dealer or call our technical support.
2
Level Adjustment(Input Gain) -
unit. This is NOT a volume control. The range is between approximently 200mV (0.2V) to 5V.
3
by over driving the input section and/or setting the input "gain" control to high. Remember that GAIN is NOT power output.
4
Crossover Selection Switch -
speakers. Use Low Pass for subwoofers. In the FLAT position, neither crossover adjustment knob has an affect and all speakers will receive the
full frequency range.
5
Input Configuration -
or from an auxiliary device (like a Smartphone, etc). The 5 channel model (HX1200.5D) is set up to accept 2/4/and 5 channels of input.
6
Frequency Adjustment -
Pass position (HPF) Low Pass (LPF) or Full Range (FULL) from the Crossover Selection Switch first. The range of adjustment is limited
between 40-400 Hz, for BOTH HPF and LPF ( and 30-300 Hz LPF on HX1200.5D sub channel). Full Range is no filter, all pass frequncy.
7
Bass Boost-
This control adds 0 to +18dB of boost at 45Hz. Be cautious when adding boost to some subwoofer systems as they may
not be able to handle the additional low frequency boost. In the 0dB position, no bass boost is added.
8
Remote Level Control -
allow the user to control the level of gain up to the maximum adjustment level set on the amplifier. The control does not add additional
boost, it only attenuates the setting that is fixed at the amplifier's control panel.
9
Sub-Sonic Adjustment -
a ported enclosure. This helps to protect the woofer from over excursion.
10
Variable Phase -
to compensate for subwoofer placement. Allowing the subwoofer to sound like it's placed in the front of the vehicle instead of the trunk.
11
Line Input(RCA) -
RCA type audio cables, keeping them away from power wiring wherever possible to reduce risk of noise.
12
Line Out (RCA)-
This output allows for easy connection of signal into multiple amplifiers without the use of "Y-adaptors" (Only
available on HX480.4/HX600.4)
13
14
Speaker Output Terminals -
connections use the LEFT + and RIGHT - as the two connections. The 4 and 5 channel amplifiers will perform into 2 Ohm stereo loads or 4 Ohm
bridged loads. HX1200.5D has a sub output that is designed for 2 ohm loads This will run 2 ohms mono, BUT NOT 1 ohm mono!
15
Power Input Connections -
8 gauge wiring for power and ground connections, 4 Gauge is recommended. Be sure any wiring that passes through metal(like firewalls)
has a grommet!
This control matches the preamp stage of the Diamond Audio amplifier to your source
These lights indicate when the amplifier is "clipping" (going into distortion) This could be casued
This switch allows you to select the crossover. Use High Pass for midrange or high frequency
This switch parallels the input circuit if you are using a single stereo pair of outputs from your headunit
Use this adjustment to select the crossover point. Remember that you must select the High
This port is for the remote level control (included with HX1200.5D). The control is intended to
This control allows you to remove the unwanted sub-sonic frequencies below the tuning frequency of
This control gives the installer a unique feature that allows the variable adjustment of phase (0 to180 degrees)
The RCA jacks allow for a normal Left and Right channel signal input. Simply connect to the source unit using
Connect your speakers to these terminals. Stereo connections are connected as labeled. Bridged
These connections are for input power, chassis ground, and remote turn-on. Use a minimum of
These lights indicate when the amplifier is powered up normally
Diamond Audio
7