Aquatec AQUAPRO AP1000FP Manual de instruções - Página 2

Procurar online ou descarregar pdf Manual de instruções para Bomba de água Aquatec AQUAPRO AP1000FP. Aquatec AQUAPRO AP1000FP 2 páginas. Pond and fountain pumps

Imprimir página

Congratulations on your purchase of this product by AquaPro,

the answers for your watergarden made easy!

VOLTAGe (V)

POWer (WATTS)

MAX HeIGHT (M)

FLOW MAX (L/H)

OuTLeT

DEsCRIPTION AND FEATUREs

Your Aquapro pond pump has been

manufactured with advanced technology to

provide you with the best quality pump for your

pond or water feature.

• Aquapro pumps are suitable for use in

many different applications including

fountains and water features, either

submersible or inline.

• Aquapro pumps are a magnetically driven

centrifugal pump, therefore they cannot

pump from a lower level when used inline.

• Your Aquapro pump has a single moving

part (an impellor set) therefore enabling

easy cleaning and maintenance.

• The motor and electrical components are

encapsulated in epoxy resin, ensuring safe

operation under water.

• The pump has a robust bearing and

shaft design so no oil/grease lubrication

is required.

• The Aquapro pumps that have plastic

encased impellor parts and ceramic shafts

(no exposed metal) may be used in salt

water applications.

• Aquapro fountain pumps are fitted with

suction cup feet, enabling use on both

horizontal and vertical surfaces.

• Check out the Aquapro range of pond

lights and accessories.

AP1000FP

AP2400FP

AP4800FP

240

2.5

4.5

1000

2400

4800

19mm

25mm

INsTALLATION

1. If required, have a qualified electrician

install weatherproof power point near

to the pond or water feature, (within the

cable length of the pump).

2. Place the pump in desired location,

ensure the pump is on a stable surface

that is free of sludge, sand and other

debris, and connect tubing to the outlet or

attach fountain kit.

3. ensure pump is submerged or properly

installed inline, then plug in power cord

and switch on.

mAINTENANCE

Disconnect power cord from the power supply

before performing maintenance. Never lift the

pump by the power cord.

The only serviceable item is the impellor set.

The motor unit of the pump is encapsulated

with epoxy resin and does not need

lubrication.

All Aquapro submersible pumps are water

cooled; if pump becomes restricted it will

overheat and could cause permanent damage.

ensure pump does not become blocked or

restricted.

The power cord cannot be replaced. If the cord

is damaged, the pump must be discarded.

The impellor set is a wearing consumable part.

Regular inspections, cleaning and maintenance

of impellor is necessary to ensure longer

impellor life.

If the impellor set becomes worn or damaged

it should be replaced (available from your dealer

or special orders). Failure to do so may cause

serious damage to pump.

1. Disconnect the power cord from

the power supply before performing

maintenance.

2. remove from water, detach tubing/

fountain kit and remove front cage or

foam prefilter from pump.

3. If using a prefilter block sponge, slide the

sponge off the threaded core and wash

out in a bucket of pond or dechlorinated

water. If you are using the internal sponge

that comes with the pump, take it out of

the cage and wash it out as above.

4. Remove the impellor cover by turning

clockwise and pulling out (it may be quite

stiff due to algae and grime build up).

Gently remove the impellor and shaft,

1 Front Cover

2 Biosponge

3 Intake Screen &

Impellor Cover

4 Inlet Adaptor*

5 Impellor

6 Motor Body

7 extendable riser

8 Bell Nozzle

9 Daisy Nozzle

10 Pump Adaptors

11 Flow Controller with

Waterfall Outlet

12 Flow Controller Adaptor

* For non-submersible applications

AP2400 Model shown.

Picture for illustration

purposes only.

POND AND FOUNTAIN PUmPs

instructions manual

use long nose pliers if needed. Take care

not to break ceramic shaft (if applicable)

because they are brittle.

5. Clean the impellor with a brush, checking

for any signs of wear or damage. If

impellor/shaft are damaged or broken,

replace immediately. If pump is run with

a damaged impellor, permanent damage

may occur.

6. reinstall the shaft, and then carefully slide

the impellor onto the shaft. The impellor

will pull itself in by magnetic force, this is

normal (take care not to pinch your fingers

or break the shaft).

7 . replace the impellor cover, making

sure the shaft is located properly on the

impellor cover. You may need to place

rubber impellor locator on end of shaft to

locate in impellor cover properly.

8. replace the internal sponge and front

cage or foam prefilter.

9. re-attach tubing/fountain kit, submerse in

water, connect to power supply and turn on.

11 12