Aquatec ocean e-vip Manual de Instruções - Página 13

Procurar online ou descarregar pdf Manual de Instruções para Ajuda à mobilidade Aquatec ocean e-vip. Aquatec ocean e-vip 16 páginas.

Imprimir página

6.12

Troubleshooting

Important!

●

The following table provides information on

faults and their probable cause. If you can-

not rectify a fault using the table, please

contact your authorised dealer directly.

●

Only trained specialists may perform serv-

ice work.

Problem

Possible

causes

When the chair is

The rechargeable

moving, a beep is

battery has al-

heard and the indi-

most no charge

cator lamp (4,

left

fig. 12) on the

hand control (1,

fig. 12) is lit

Indicator lamp

Control is faulty

●

"SERVICE" (6,

Software error

●

fig. 12) on the

Button for emer-

●

hand control is lit

gency lowering

is faulty

Power outage

●

while the chair is

moving

Drive is faulty

●

Hand control is

●

faulty

Seat frame does

The load limit has

not move up

been exceeded

Cable inserted in-

correctly

Connection plug

board not at-

tached

Cable on the con-

trol inserted incor-

rectly

Connecting cable

(3, fig. 9) pulled off

Connecting cable

not inserted all the

way

Control is faulty

Rechargeable bat-

tery is flat

Cable for the hand

control is inserted

incorrectly

Hand control is

faulty

Remedy

Recharge the bat-

tery (see

section 5.2)

Carry out a reset

(see below)

Load max. 150 kg

Insert cable prop-

erly

Attach the con-

nection plug board

(clicks in)

Motor for tilt ad-

justment is al-

ways circuit 3

Replace cable

Insert cable all the

way and close the

safety bracket

Carry out a reset

(see below)

Recharge the bat-

tery (see

section 5.2) or use

a replacement

Insert cable all the

way

Carry out a re-

●

set (see below)

Replace hand

●

control

Problem

Possible

causes

Seat frame does

Cable inserted in-

not move down

correctly

Connection plug

board not at-

tached

Cable on the con-

trol inserted incor-

rectly

Connecting cable

(3, fig. 9) pulled off

Connecting cable

not inserted all the

way

Control is faulty

Rechargeable bat-

tery is flat

Cable for the hand

control is inserted

incorrectly

Hand control is

faulty

Seat frame does

Cable inserted in-

not tilt

correctly

Connection plug

board not at-

tached

Cable on the con-

trol inserted incor-

rectly

Connecting cable

(3, fig. 9) pulled off

Connecting cable

not inserted all the

way

Control is faulty

Rechargeable bat-

tery is flat

Cable for the hand

control is inserted

incorrectly

Hand control is

faulty

Remedy

Insert cable prop-

erly

Attach the con-

nection plug board

(clicks in)

Motor for tilt ad-

justment is al-

ways circuit 3

Replace cable

Insert cable all the

way and close the

safety bracket

Carry out a reset

(see below)

Recharge the bat-

tery (see

section 5.2) or use

a replacement

Insert cable all the

way

Carry out a re-

●

set (see below)

Use the button

●

for emergency

lowering

Insert cable prop-

erly

Attach the con-

nection plug board

(clicks in)

Motor for tilt ad-

justment is al-

ways circuit 3

Replace cable

Insert cable all the

way and close the

safety bracket

Carry out a reset

(see below)

Recharge the bat-

tery (see

section 5.2) or use

a replacement

Insert cable all the

way

Carry out a re-

●

set (see below)

Replace hand

●

control