HP 5120-24G-PoE+ EI Manual de configuração - Página 32

Procurar online ou descarregar pdf Manual de configuração para Interruptor HP 5120-24G-PoE+ EI. HP 5120-24G-PoE+ EI 39 páginas. Hp 5120 ei switch series
Também para HP 5120-24G-PoE+ EI: Ficha de dados (17 páginas)

Imprimir página

HP 5120-24G-PoE+ EI Manual de configuração

# Change the member ID of Device B to 2.

<DeviceB> system-view

[DeviceB] irf member 1 renumber 2

Warning: Renumbering the switch number may result in configuration change or loss.

Continue? [Y/N]:y

[DeviceB]

Power off the devices, connect IRF links as shown in

Configure IRF port bindings:

# Bind Ten-GigabitEthernet 1/1/2 to IRF-port 1/2 on Device A and save the configuration.

<DeviceA> system-view

[DeviceA] interface ten-gigabitethernet 1/1/2

[DeviceA-Ten-GigabitEthernet1/1/2] shutdown

[DeviceA-Ten-GigabitEthernet1/1/2] quit

[DeviceA] irf-port 1/2

[DeviceA-irf-port1/2] port group interface ten-gigabitethernet 1/1/2

[DeviceA-irf-port1/2] quit

[DeviceA] interface ten-gigabitethernet 1/1/2

[DeviceA-Ten-GigabitEthernet1/1/2] undo shutdown

[DeviceA-Ten-GigabitEthernet1/1/2] save

# Bind Ten-GigabitEthernet 2/1/1 to IRF-port 2/1 on Device B and save the configuration.

<DeviceB> system-view

[DeviceB] interface ten-gigabitethernet 2/1/1

[DeviceB-Ten-GigabitEthernet2/1/1] shutdown

[DeviceB-Ten-GigabitEthernet2/1/1] quit

[DeviceB] irf-port 2/1

[DeviceB-irf-port2/1] port group interface ten-gigabitethernet 2/1/1

[DeviceB-irf-port2/1] quit

[DeviceB] interface ten-gigabitethernet 2/1/1

[DeviceB-Ten-GigabitEthernet2/1/1] undo shutdown

[DeviceB-Ten-GigabitEthernet2/1/1] save

# Activate IRF port configuration on Device A.

[DeviceA-Ten-GigabitEthernet1/1/2] quit

[DeviceA] irf-port-configuration active

# Activate IRF port configuration on Device B.

[DeviceB-Ten-GigabitEthernet2/1/1] quit

[DeviceB] irf-port-configuration active

After the IRF port configuration is activated, the two devices automatically elect a master. In this

example, Device A is the master. Device B automatically reboots and joins the Device A as a

subordinate to form an IRF fabric. The system name of the IRF fabric is DevcieA.

Configure LACP MAD:

# Create a dynamic aggregate interface and enable LACP MAD. Because LACP MAD is not run

between IRF domains, you can use the default value 0.

<DeviceA> system-view

[DeviceA] interface bridge-aggregation 2

[DeviceA-Bridge-Aggregation2] link-aggregation mode dynamic

[DeviceA-Bridge-Aggregation2] mad enable

You need to assign a domain ID (range: 0-4294967295)

Figure

12, and power on the two devices.