Panasonic PT-DW100 Brochura e especificações - Página 4

Procurar online ou descarregar pdf Brochura e especificações para Projetor Panasonic PT-DW100. Panasonic PT-DW100 4 páginas. 3-chip dlp projector highly reliable wide 10,000 lm projector
Também para Panasonic PT-DW100: Ficha de especificações (10 páginas), Especificações (4 páginas)

Imprimir página

Specifications

Power supply

North America: 120–240 V AC, 16 – 9.0 A, 50/60 Hz (3-wire single-phase)

Europe, Asia: 220–240 V AC, 9.5 A, 50/60 Hz (3-wire single-phase)

Power consumption

North America: 1,600–1,500 W (10-15 W in standby mode with fan stopped)

Europe, Asia: 1,500 W (15 W in standby mode with fan stopped)

DLP

chip

Panel size

0.85" diagonal (16:9 aspect ratio)

™

Display method

DLP

™

chip x 3 (R, G, B), DLP

Pixels

1,049,088 (1,366 x 768) x 3, total of 3,147,264 pixels

Lens

Optional powered zoom/focus lenses

Lamp

300 W UHM lamp x 4 (four lamp system)

Screen size

70 - 600 inches,16:9 aspect ratio

(70-300 inches, 16:9 aspect ratio with the ET-D75LE5)

Brightness*

10,000 lumens (four-lamp operation mode)

Contrast ratio*

5,000:1 (full on/full off, in Dynamic iris 3 mode)

Resolution

1,366 x 768 pixels (Input signals that exceed this resolution will be converted to 1,366 x 768 pixels.)

RGB input scanning frequency

fH 15-100 kHz, fV 24-120 Hz

Dot clock 20-162 MHz

Component signal

480i, 480p, 576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p,

1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p

Video signal

fH 15.75/15.63 kHz, fV 50/60Hz

(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM)

Lens shift

Vertical: ±70% (±60% with the ET-D75LE6) (powered)

Horizontal: ±30% (±20% with the ET-D75LE6) (powered)

Keystone correction range

Vertical: ±40° (±22° with the ET-D75LE5, ±28° with the ET-D75LE6)

Terminals

DVI-D IN

DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link

480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,

720/60p, 720/50p

VGA (640 x 480) – WUXGA*

Dot clock: 25–162 MHz

RGB1/YP

BNC x 5

RGB2 IN

D-sub HD 15-pin x 1

VIDEO IN

BNC x 1, 1.0 Vp-p

VIDEO OUT

BNC x 1, 1.0 Vp-p

S-VIDEO IN

Mini DIN 4-pin x 1

LAN

RJ-45 (10 Base-T/100 Base-TX) x 1, compatible with PJLink™

SERIAL IN

D-sub 9-pin female x 2 (RS232C x 1, RS422 x 1)

SERIAL OUT

D-sub 9-pin male x 1 (RS422 x 1)

REMOTE 1 IN

M3 jack x 1 for wired remote control

REMOTE 1 OUT

M3 jack x 1 for link control

REMOTE 2 IN

D-sub 9-pin female x 1 for external control (parallel)

Optional board slot With ET-MD77SD1

SERIAL IN: BNC x 1, SD-SDI signal (YC

installed*

SERIAL OUT: BNC x 1, active through

With ET-MD77SD3

SERIAL IN: BNC x 1, SD-SDI signal (YC

installed*

Single-link HD-SDI signal (YC

1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p

SERIAL OUT: BNC x 1, active through

With ET-MD100SD4

Link A/Link B IN: BNC x 1 for each, SD-SDI signal (YC

installed

Single-link HD-SDI signal (YC

1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p

Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE 372M compliant: 1920 x 1080/50i,

1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p

Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit): 2048 x 1080/24p, 2048 x 1080/24sF

With ET-MD77DV

Specifications are the same as those for the DVI-D IN terminal on the main unit.

installed

Installation

Front/rear, ceiling/floor

Power cord length

3.0 m (9.8')

Dimensions (W x H x D)

578 x 320 x 643 mm (22-3/4" x 12-19/32" x 25-5/16") (without lens)

Weight*

Approx. 35 kg (77.2 lbs) without lens

Operating temperature

0 -45 °C (32 -113 °F)*

Operating humidity

10-80% (no condensation)

Supplied accessories

Power cord, Wireless/wired remote control unit,

Batteries for remote control (North/South America: AA type x2, Europe/Asia: R6/LR6 type x 2), Eye bolt x4, Wire rope

Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.

Only when using VESA CVT-RB(Reduced Blanking) signals.

The LAN terminal on each board, when mounted, cannot be used because the LAN terminal on the main unit has priority.

Average value. May differ depending on models.

The operating temperature range is 0°C (32°F) to 40°C (104°F) when used in High-Altitude mode (1,400 m [4,593 feet] to 2,700 m [8,858 feet]).

Also, if the ambient temperature exceeds 40°C (104°F) (35°C [95°F] in High-Altitude mode) when using all four lamps, the light output may be

reduced approximately 30% to protect the projector.

Projection distance

Diagonal image size

ET-D75LE6

(aspect raio: 16:9)

1.0-1.2:1

min.

max.

1,560 mm

1,865 mm

70"

5.1'

6.1'

2,253 mm

2,696 mm

100"

7.4'

8.8'

3,408 mm

4,081 mm

150"

11.2'

13.4'

4,563 mm

5,466 mm

200"

15.0'

17.9'

6,873 mm

8,236 mm

300"

22.6'

27.0'

9,183 mm

11,006 mm

400"

30.1'

36.1'

13,803 mm

16,546 mm

600"

45.3'

54.3'

NOTES ON USE

1. Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may result in fire,

malfunction, or electric shock.

2. The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to

illuminate, due to impact or extended use.

3. The projector uses high-wattage lamp that becomes very hot during operation. Please observe the following precautions.

• Never place objects on top of the projector while it is in operation.

• Make sure there is an unobstructed space of 500 mm or more around the projector's exhaust openings.

• Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.

When stacking projector units, be sure to provide the amount of space indicated between them. These space requirements also apply to

installation where only one projector unit is operating at one time and the other unit is used as a backup.

• If the projector is placed in a box or enclosure, temperature of the air surrounding the projector must be between 0°C and 35°C. Also make sure the

projector's intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake.

™

projection system

(1,920 x 1,200), compatible with non-interlaced signals only,

4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i

4:2:2 10-bit): SMPTE 292M compliant: 720/50p, 720/60p,

4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i

4:2:2 10-bit): SMPTE 292M compliant: 720/50p, 720/60p, 1080/50i,

ET-D75LE1

ET-D75LE2

1.5-2.0:1

2.1-3.1:1

min.

max.

min.

2,322 mm

3,103 mm

3,137 mm

7.6'

10.2'

10.3'

3,349 mm

4,476 mm

4,516 mm

11.0'

14.7'

14.8'

5,062 mm

6,765 mm

6,814 mm

16.6'

22.2'

22.4'

6,775 mm

9,053 mm

9,112 mm

22.2'

29.7'

29.9'

10,201 mm

13,630 mm

13,707 mm

33.5'

44.7'

45.0'

13,626 mm

18,206 mm

18,303 mm

44.7'

59.7'

60.0'

20,477 mm

27,360 mm

27,494 mm

67.2'

89.8'

90.2'

Optional Accessories

Lens

Zoom lens

ET-D75LE6 (1.0-1.2:1)

ET-D75LE1 (1.5-2.0:1)

ET-D75LE2 (2.1-3.1:1)

ET-D75LE3 (3.1-5.2:1)

ET-D75LE4 (5.2-8.2:1)

ET-D75LE8 (8.2-15.4:1)

Fixed focus lens

ET-D75LE5 (0.8:1)

ET-D75LE1

Lamp

Replacement lamp unit

ET-LAD12K

ET-LAD12KF (four pack)

Ecological-conscious design

Panasonic works from every angle to minimize environmental impact in the

product design, production and delivery processes, and in the performance of

the product during its life cycle. The PT-DW100 reflects the following

ecological considerations.

•Lead-free solder is used to mount components to the printed circuit boards.

•Lamp power switching further reduces power consumption.

•Auto Power Save activates standby mode when no signal is input.

Dimensions

Throw distance

ET-D75LE3

3.1-5.2:1

max.

min.

max.

4,719 mm

4,730 mm

7,937 mm

15.5'

27.9'

6,787 mm

6,798 mm

11,391 mm

22.3'

39.9'

10,234 mm

10,244 mm

17,147 mm

33.6'

59.9'

13,680 mm

13,691 mm

22,904 mm

44.9'

79.9'

20,574 mm

20,584 mm

34,416 mm

67.5'

119.9'

27,467 mm

27,477 mm

45,929 mm

90.1'

159.9'

41,254 mm

41,264 mm

68,954 mm

135.3'

135.4'

239.9'

4. If the projector is to be operated continuously 24 hours a day, use the multi-lamp optical system's alternating lamp operation (lamp changer)

function. The projector can be operated continuously 24 hours a day in four-lamp operation mode, but it will automatically operate with three

lamps for 8 hours of the 24 hours.

5. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.

• The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage

conditions.

• The brightness of the lamp will gradually decrease with use.

6. Because the ET-D75LE5 is a fixed short-throw lens, the lens shift function cannot be used with it.

7. Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp performance.

may be subject to export regulations. VGA and XGA are trademarks of International Business Machines Corporation.

Input signal board

Frame

ET-PFD100

SD-SDI input signal board

ET-MD77SD1

HD/SD-SDI input signal board

ET-MD77SD3

Carrying handle

ET-HAD100

Dual link HD/HD-SDI input

signal board

ET-MD100SD4

Ceiling mount bracket

DVI-D input signal board

High-ceiling

ET-MD77DV

mount bracket

ET-PKD100H

Smoke cut filter

ET-SFD100

This optional

smoke filter must be used

ET-PKD100H

for staging events where

smoke or fog is dispersed.

Made in Japan

PT-DW100 projector is

carefully manufactured at

the Panasonic factory in Japan

under strict quality control. This is

another very important advantage

of Panasonic projectors.

578 (22-3/4")

ET-D75LE4

ET-D75LE8

5.2-8.2:1

8.2-15.4:1

min.

max.

min.

7,943 mm

12,713 mm

12,430 mm

27.9'

41.7'

40.8'

11,397 mm

18,206 mm

17,923 mm

39.9'

59.7'

58.8'

17,153 mm

27,359 mm

27,077 mm

59.9'

89.8'

88.8'

22,909 mm

36,512 mm

36,232 mm

79.9'

119.8'

118.9'

34,422 mm

54,819 mm

54,541 mm

119.9'

179.9'

178.9'

45,934 mm

73,126 mm

72,850 mm

159.9'

239.9'

239.0'

68,960 mm

109,740 mm

109,468 mm

239.9'

360.0'

359.1'

For more information about Panasonic projectors

http://panasonic.net/avc/projector

EC98J2010

JQA-0443

Factories of Systems Business Group have received

ISO14001:2004 – the Environmental Management System

certification. (Except for 3rd party's peripherals.)

Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product

All other trademarks are the property of their respective trademark owners.

DLP, DLP logo and DLP Medallion logo are trademarks or registered trademarks of Texas Instruments.

The PJLink trademark is an application trademark in Japan, the United States, and other

All information included here is valid as of February 2010.

Low-ceiling

mount bracket

ET-PKD100S

unit: mm (inch)

ET-D75LE5

0.8:1

max.

fixed

23,652 mm

1,151 mm

77.6'

3.8'

33,943 mm

1,681 mm

111.4'

5.5'

51,095 mm

2,563 mm

167.6'

8.4'

68,246 mm

3,445 mm

223.9'

11.3'

102,549 mm

5,209 mm

336.4'

17.1'

136,852 mm

—

449.0'

205,458 mm

—

674.1'

Projection Images simulated.

countries and regions or registered trademarks.

PT-DW100-2 Printed in Japan.