Diamondback 180 Manual de instalação
Procurar online ou descarregar pdf Manual de instalação para Acessórios para automóveis Diamondback 180. Diamondback 180 2 páginas. For toyota tacoma 2005; toyota tacoma 2006; toyota tacoma 2007; toyota tacoma 2008; toyota tacoma 2009; toyota tacoma 2010; toyota tacoma 2011; toyota tacoma 2012; toyota tacoma 2013; toyota tacoma 2014; toyota tacoma 2015; toyota tacoma 2016; toyota taco
Também para Diamondback 180: Manual de instalação (2 páginas), Manual de instalação (2 páginas), Manual de instalação (2 páginas)
Imprimir páginaDiamondBackCovers.com / 800 935 4002
INSTALLATION GUIDE
75 minutes
Normal install time
PARTS INCLUDED:
180 Cover
TOOLS REQUIRED:
3/8" Nut
Drill
Driver
PREPARE THE BULKHEAD
Attach the clamp bracket to the bulkhead, centered side to side,
1
flush with the top rail, and longer leg down using a drill, 3/8" nut driver
bit, and four self-drilling screws.
Installing the clamp bracket is easiest if you pre-drill it using
the screws.
Attach a lock-rod striker bracket to each front corner of the cargo
2
bed, the bracket's V bend pointing rearward and the side flange
located as high as possible without it breaking the plane of the top
of the bed rail, using a drill, 3/8" nut driver bit, two self-drilling
screws, and the two slots nearest the ends of the bracket.
Detach all three brackets by removing the self-drilling screws.
3
Use the holes in the truck body
4
left by the self-drilling screws
as pilot holes to drill larger,
3/8" holes.
Keep an eye out for these icons:
Clamp Bracket
Threaded Insert
Installation Tool
9/16"
3/8" Bit
Hammer
Wrench
IMPORTANT!
Important installation information
Lock-Rod Striker
Brackets (2)
× 12
× 12
1/4" Plain
1/4" Hex
Washers (12)
Bolts (12)
Ratchet
7/16"
9/16"
Wrench
Socket
Socket
Hammer a rivet nut into each hole.
5
Do not install rivet nuts through plastic bed rail caps or plastic
bedliners. (Spray-on bedliners are fine.) Use a utility knife to
trim the plastic so that the rivet nuts' outer flange can sit
tightly against the body of the truck itself.
Insert the installation-tool mandrel into a rivet nut. Hand-tighten
6
it until its hexagonal sleeve is tight to the face of the rivet nut.
Use a 9/16" wrench to hold the installation-tool
7
sleeve as you tighten the mandrel with a 7/16"
socket until the rivet nut deforms and locks
against the interior of the bed wall.
You'll know the rivet
nut is fully com-
pressed when you
feel the mandrel
become very difficult
to turn.
Remove the installation tool by unscrewing the mandrel.
8
Repeat steps 6-8 for each rivet nut.
9
Reinstall all three brackets using
10
the hex bolts, plain washers, and a
7/16" socket.
Do not overtighten the bolts or you might strip the rivet nuts.
If you are also installing a Cross Bin, do so now. Refer to page 2 of
11
the Cross Bin Installation Guide for details.
Helpful Hints
Tips to assist installation
× 8
× 12
1/4" Self-Drilling
1/4" Rivet
Screws (8)
Nuts (12)
× 2
Cap
1/8" Hex
Clamps (2)
Key
PRE-INSTALLATION
NOTE:
If your truck has bed rail caps,
you should affix the included
bulkhead prep kit prior to
installing the DiamondBack 180.
Marker
CONTINUED ON REVERSE >
180
270
CVR-180.1
Gas
Springs (4)