Axminster 100090 Manual do utilizador - Página 7

Procurar online ou descarregar pdf Manual do utilizador para Serra Axminster 100090. Axminster 100090 12 páginas. Metal cutting bandsaw

Imprimir página

Setting up the Machine

The machine has been set up in the factory. If, however, you think the settings may have been

moved due to a 'knock' or whatever, proceed to set the machine up as follows:-

Disconnect the machine from the mains supply.

Remove the front cover by undoing the 5 off M4 caphead bolts, remove them and the shakeproof

washers, place carefully aside.

Clean the machine completely.

Withdraw the blade guide assemblies to their furthest extremes, (leaving the maximum expanse

of blade exposed.) Open up the drive belt and pulley cover and turning one of the pulleys move

the blade and check the teeth and the fabric of the blade, (no cracks etc.), if all seems ok, check

the blade is under reasonable tension, and reconnect the machine to the supply. Stand on the

side of the machine away from the open frame and start the machine.

Allow it to run up to speed. Once the saw is running, carefully move to the front left side of the

saw and check the blade is tracking correctly, i.e. more or less in the centre of the wheel, not too

far off the front of the wheel. If the blade is running too far to the front, adjust the tracking by

screwing 'in' the tracking control bolt (see fig 9a),only adjust in small increments and wait for it to

take affect. If the tracking is too far to the rear (scuffing against the rim) 'unscrew' the tracking

control bolt NOTE if you unscrew the bolt be prepared to 'tighten the blade' a touch. Once the

blade is running correctly, switch the machine off. Disconnect the machine from the mains

supply. Replace the front cover.

Pull the saw down, turn the swivel base against the preset stop and using a good square set

against the rear jaw of the vice, check the blade of the square lies along saw blade. If it is out of

square, adjust the position of the swivel base, by adjusting the preset stop, until the correct angle

is reached. Check that the base remains in position when the base clamp is tightened. Adjust the

index pointer.

Move the guide assemblies as close together as possible, leaving a small gap near the rear vice

jaw where you can stand a square. Stand the square on the floor of the vice with the blade of the

square up, check that the saw blade is vertical. The blades can be 'twisted' a little bit more, or

untwisted by loosening the main bolt that holds the bearing guide block onto the slides, moving

fractionally (there is only a small amount of 'slop' in the guide land and the groove between the

guide block assembly and the slide mechanism) and retightening.

Check the blade is pressed firmly between the two side rollers. If not, remove the safety cover

plates and adjust the rollers, by loosening the lock nuts (the top ones), and moving the bearing

using the eccentric cam profile (turn the bottom hexagons) of the mountings. DO NOT PUSH

THE BLADE OUT OF LINE by over adjusting (The blade should be in line with the groove in the

trust bearing). (See figs 9b & 9c)

When adjustment is complete re-tighten the lock nuts and replace the safety covers. Recheck

when everything is retightened. Reconnect the machine and run up to speed. Check everything

looks and sounds normal.

Axminster No.

Metal Cutting Bandsaw

Makers Number:

Motor:

Blade Speeds:

Max cutting Capacities @ 90˚

Round Bar:

Square Bar:

Max Cutting Capacities @ 45˚

Round Bar:

Square Bar:

Blade Size:

Saw Body Swivel

Footprint:

Weight

Noise level in accordance with DIN 45635

Offload:

Working:

IT IS RECOMMENDED THAT YOU WEAR EAR PROTECTION

WHEN USING THIS MACHINE

Specifications

100090

G4012

230v 50Hz 550W

20, 30, 50, M /min

110mm diameter

100mm x 150mm

70mm diameter

85mm x 65mm

1640L, 14 T.P.I., 0.65mm Thickness, 13mm Wide

915mm L x 575mm W x 1010mm H

70 Kgs

> 60db(A)

60-65 db(A)

0-45˚