Axminster Trade 105781 Manual de instruções original - Página 4
Procurar online ou descarregar pdf Manual de instruções original para Purificador Axminster Trade 105781. Axminster Trade 105781 16 páginas. Cyclone extractors
Também para Axminster Trade 105781: Manual de instruções original (16 páginas)
Imprimir página
GENERAL INSTRUCTION FOR 230V MACHINES
Good Working Practices/Safety
The following suggestions will enable you to observe
good working practices, keep yourself and fellow workers
safe and maintain your tools and equipment in good
working order.
WARNING!! KEEP TOOLS AND EQUIPMENT OUT
OF THE REACH OF YOUNG CHILDREN
Mains Powered Tools and Machines
Primary Precautions
These machines are supplied with a moulded 16 Amp
plug and 3 core power cable. Before using the machine,
inspect the cable and the plug to make sure that neither
are damaged. If any damage is visible, have the damaged
item inspected/repaired by a suitably qualified person.
If it is necessary to replace the plug, it is preferable to
use an 'unbreakable' type that will most resist damage.
Only use a 16 Amp plug, and make sure the cable clamp
is tightened securely. Fuse as required. If extension leads
are to be used, carry out the same safety checks on them,
and ensure that they are correctly rated to safely supply
the current that is required for your machine. Remember,
most machines or tools have handles or holding
positions, the power cable is not one of them.
Workplace/Environment
The machine is not designed for use outside. Keep the
machine clean; it will enable you to more easily see any
damage that may have occurred. Clean the machine with
a damp soapy cloth if needs be, do not use any solvents
or cleaners, as these may cause damage to any plastic
parts or to the electrical components.
It is good practice to leave the machine unplugged until
work is about to commence, also make sure to unplug
the machine when it is not in use, or unattended. To
avoid inadvertent 'start up' , if your machine is not fitted
KEEP THE WORK AREA AS UNCLUTTERED AS
IS PRACTICAL, THIS INCLUDES PERSONNEL
AS WELL AS MATERIAL.
UNDER NO CIRCUMSTANCES SHOULD
CHILDREN BE ALLOWED IN WORK AREAS.
with a NVR system, ensure the switch is always returned
to the OFF position. Once you are ready to commence
work, remove any tools, objects or items that could
inadvertently get 'sucked up' by the machine and place
safely out of the way. Re-connect the machine, ensuring
the power cable is not 'snagged' or routed where it could
be tripped over as you move about the workshop; it is
not too close to an unguarded heat source, or is laid over
or around a sharp edge. If the work you are carrying out
is liable to generate flying grit, dust or chips, wear the
appropriate safety clothing, goggles, gloves, masks etc.
If the work operation appears to be excessively noisy,
wear ear-defenders. If you wear your hair in a long style,
wearing a cap, safety helmet, hairnet, even a sweatband,
will minimise the possibility of your hair being caught
up in the rotating parts of the machine, likewise,
consideration should be given to the removal of rings
and wristwatches if these are liable to be a 'snag' hazard.
Consideration should also be given to non-slip footwear,
etc.
use this machine if you are tired, your attention is
Do not
wandering or you are being subjected to distraction.
use this machine within the designated safety
Do not
areas of flammable liquid stores or in areas where there
may be volatile gases. There are very expensive, very
specialised machines for working in these areas. Above
all,
make sure you know what is happening
OBSERVE....
around you, and
USE YOUR COMMON SENSE.
SPECIFIC SAFETY
FOR DUST EXTRACTORS
use this machine as a vacuum cleaner, try to keep
Do not
the waste medium to wood by products.
uplift workshop floor debris (stones, nails, screws,
Do not
paper etc., etc). Be aware that wood dust is an explosive
medium.
allow any 'naked light' source to occur anywhere
Do not
near the machine. This includes cigarettes, matches, etc,
and do not place the machine near any unprotected light
bulbs, that could possibly get broken.
The suction force is generated by a high speed fan unit.
This has the potential to amputate fingers, grab loose
clothing (ties etc.,) and 'bat' large chips etc, at high
speeds. Keep all guarding in place, and if access to the fan
becomes necessary (due to blockage etc.,) disconnect
the machine from the mains supply and ensure the fan
has come to a complete stop before putting your hands
anywhere near to it.
If you are not using 'clear' extraction hose, periodically
remove the hose to check that the inlet to the machine
is not getting restricted. (The safety guard grill of the
inlet duct can be particularly irksome in this way, as long
strand shavings etc., can wrap around the grill fret.)
4