Axor Citterio 39451 7 Series Manual de instruções de utilização - Página 3

Procurar online ou descarregar pdf Manual de instruções de utilização para Produto de canalização Axor Citterio 39451 7 Series. Axor Citterio 39451 7 Series 16 páginas.

Imprimir página

S A F E T Y N O T E S

Gloves should be worn during installation to prevent

crushing and cutting injuries.

The product may only be used for bathing, hygienic

and body cleaning purposes.

Children as well as adults with physical, mental and ⁄or

sensoric impairments must not use this product without

proper supervision. Persons under the influence of

alcohol or drugs are prohibited from using this product.

Do not allow the streams of the shower touch sensitive

body parts (such as your eyes). An adequate distance

must be kept between the shower and you.

The product may not be used as a holding handle. A

separate handle must be installed.

The hot and cold supplies must be of equal pressures.

I N S T A L L A T I O N I N S T R U C T I O N S

⁄ Prior to installation, inspect the product for transport

damages. After it has been installed, no transport or

surface damage will be honoured.

⁄ The pipes and the fixture must be installed, flushed and

tested as per the applicable standards.

⁄ The plumbing codes applicable in the respective

countries must be observed.

⁄ The mesh washer must be insert to protect the shower

against incoming dirt by pipework. Incoming dirt leads

to defects or⁄and can damage parts of the shower;

such caused faults voids all liability and guarantee

claims.

F A U L T

⁄ Insufficient water

⁄ Mixer stiff

⁄ Mixer dripping

⁄ Water escaping in area of swivel

spout

⁄ Spout temperature does not

correspond with temperature set

⁄ Instantaneous heater didn't work

A S S E M B L Y (see page 04 )

T E C H N I C A L D A T A

Operating pressure:

Recommended operating pressure:

Test pressure:

Hot water temperature:

Thermal disinfection:

The product is exclusively designed for drinking water!

S Y M B O L D E S C R I P T I O N

C A U S E

⁄ Shower filter seal dirty

⁄ Cartridge defective, calcified

⁄ Cartridge defective

⁄ O-ring defective

⁄ Hot and cold supplies are reversed

⁄ Shower filter seal dirty

⁄ Flow limiter in handshower isn't re-

moved

(1 MPa = 10 bar = 147 PSI)

Do not use silicone containing acetic acid!

Hot and cold supplies are reversed

(see page 11 )

M A I N T E N A N C E (see page )

D I M E N S I O N S (see page 06 )

F L O W D I A G R A M (see page 07)

S P A R E P A R T S (see page 15 )

XX = Colors

00 = Chrome Plated

34 = Brushed Black Chrome

99 = Polished Gold-Optic

S P E C I A L A C C E S S O R I E S

(order as an extra)

⁄ extension 60 mm #93882000 (see page 15 )

C L E A N I N G (see page 08 )

O P E R A T I O N (see page 07)

R E M E D Y

⁄ Clean filter seal between shower and

hose

⁄ Exchange cartridge

⁄ Exchange O-ring

⁄ Install function block turned through

180º (see page 11 )

⁄ Clean filter seal between shower and

hose

⁄ Remove flow limiter

0 3

max. 1 MPa

0,1 - 0,5 MPa

1,6 MPa

max. 60°C

70°C ⁄ 4 min