Epson 24-PIN DOT MATRIX PRINTER LQ-680PRO Manual do utilizador - Página 11

Procurar online ou descarregar pdf Manual do utilizador para Impressora Epson 24-PIN DOT MATRIX PRINTER LQ-680PRO. Epson 24-PIN DOT MATRIX PRINTER LQ-680PRO 17 páginas. 24-pin dot matrix printer
Também para Epson 24-PIN DOT MATRIX PRINTER LQ-680PRO: Manual do utilizador (22 páginas), Referência rápida (12 páginas), Especificações (2 páginas), Especificações (3 páginas), Manual de referência (34 páginas), Manual de configuração (2 páginas)

Epson 24-PIN DOT MATRIX PRINTER LQ-680PRO Manual do utilizador

Using Postcards

You can print on a variety of postcards, loading them the same
way you load single sheets: from the paper guide or with the
optional cut-sheet feeder. (For instructions on loading single
sheets, see the User's Guide.)
Before printing, make sure the paper thickness lever is set to
or
. Then select
Auto
2
Card
button on the control panel.
Paper
Load postcards printable side up, top edge first.
Card mode is available only when the paper thickness
lever is set to Auto or 2 or higher on the scale.
When printing on postcards, make sure that your
software settings keep the printing entirely within the
printable area. Printing on the edge of a postcard can
damage the print head. For more information, see the
paper specifications on "Printable Area" on page 5.
Use postcards only under normal operating conditions.

Using Micro Adjust

The micro adjust feature allows you to move paper forward or
backward in 1/180-inch increments. You can use this feature to
adjust the loading, printing, and tear-off positions.

Adjusting the Loading Position

The loading position is the position of the paper after the
printer loads it. If your printing appears too high or low on the
page, you can change the loading position with the micro adjust
feature described below.
Top margin settings made in some application software
override adjustments you make to the loading position
with the micro adjust feature. If necessary, adjust the
loading position in your software.
1. Make sure the printer is turned on. If necessary, lift up the
printer cover so you can see the paper position.
2. Load either continuous or single-sheet paper. (Press the
button to load continuous paper from the
Load/Eject
tractor or a single sheet from the optional cut-sheet feeder.)
3. Hold down the
Pause
light starts flashing and the printer enters the micro
Pause
adjust mode.
by pressing the
Tear Off/Special
button for about three seconds. The
4. Press the
D button to move the paper toward the
LF/FF
front of the printer, or press the
move the paper toward the rear. The new loading position is
set to the position where you release the buttons.
When loading a sheet from the front (from the paper
guide), pressing the LF/FF
position toward the top of the page. When loading a
sheet from the rear (from the cut-sheet feeders or the
tractor), pressing the LF/FF
loading position toward the bottom of the page.
The printer has a minimum and a maximum loading
position. If you try to adjust the loading position beyond
these limits, the printer beeps and stops moving the
paper.
When the paper reaches the factory-set loading
position, the printer beeps and paper feeding pauses
briefly. Use the factory setting as a reference point
when adjusting the loading position.
If you want to eliminate the top margin and print at the
very top of the page, adjust the loading position so that the
top of the paper lines up with the raised line on the ribbon
mask, as shown below.
5. After you set the loading position, press the
to turn off micro adjust mode.
For both single-sheet and continuous paper, your loading
position setting remains in effect until you change it, even if you
turn off the printer.
11/00
EPSON LQ-680Pro
U button to
Load/Eject
D
button moves the loading
D
button moves the
raised line
button
Pause
EPSON LQ-680Pro
11
-